Abstract:In this work, the effect of pulsed magnetic treatment (PMT) on the microstructure of TC4 titanium alloy was investigated. TC4 titanium alloy is widely used in the manufacture of the blade of aviation engine. The microstructure of TC4 titanium alloy determines its property. PMT is a novel method used to modify the microstructures of alloys and has been explored in several papers recently. PMT has many advantages in the aspect of efficiency, energy-saving, non-deformation, etc. Therefore, the effect of PMT on the microstructures of TC4 titanium alloy was explored in this work. The variation of the dislocation density and the grain boundary angle of TC4 titanium alloy was observed after PMT. In the experiment, the magnetic induction density is 2 T, the pulse frequency is 5 Hz and the pulse number is 100. According to XRD tests, the dislocation density in TC4 alloy after PMT increased about 10.9%. KAM maps in EBSD test were used for evaluating the same area's dislocation density of the TC4 alloy before and after PMT. The dislocation distribution of TC4 titanium alloy changes notably: the in-grain dislocation density became more homogeneous and some local high-density areas disappeared, the distribution of dislocation near grain boundaries caused the angles of the grain boundaries altered and the fraction of low-angle grain boundaries decreased while the fraction of Sigma 11 grain boundaries (CSL grain boundary) increased. The motivation mechanism of the dislocation in TC4 titanium alloy under PMT was speculated based on the experimental results and some previous researches. The PMT may change the energy state of the electrons in pinning area of dislocations, which accelerates the electrons transformation from singlet state to triplet state and then increases the mobility of the vacancy or impurity atoms so that the dislocation depinning could occur under the original stress field and thus leads to dislocation movement and transformation of microstructure.

Strengthening Mechanism of 45crnimova Steel by Pulse Magnetic Treatment

Magnetic induced re-dissolution and microstructure modifications on mechanical properties of Cr4Mo4V steel subjected to pulsed magnetic treatment

Effect of a pulsed magnetic treatment on the dislocation substructure of a commercial high strength steel

Improvement in uniformity of alloy steel by pulsed magnetic field treatment

Mechanism and Application of Mechanical Property Improvements in Engineering Materials by Pulsed Magnetic Treatment: A Review

Pulsed Magnetic Treatment of Cobalt for Enhanced Microstructures and Mechanical Properties

Plastic Deformation Caused by Pulsed Magnetic Treatment of Mid-Carbon Steel

Effects of Pulsed Magnetic Fields of Different Intensities on Dislocation Density, Residual Stress, and Hardness of Cr4Mo4V Steel

Influence of a high pulsed magnetic field on the tensile properties and phase transition of 7055 aluminum alloy

Effect of high magnetic field treatment on the microstructure and mechanical properties of Ti-48Al-2Cr-2Nb alloy prepared by powder-hot isostatic pressing

Effect of Pulsed Magnetic Field on Microstructure and Mechanical Properties of 7050 Al Alloy After Two-Stage Aging

Effects of pulse magneto-oscillation on GCr15 bearing steel continuous casting billet

Optimizing Heat Treatment to Improve the Microstructures and Mechanical Properties of 5crnimov Steel

Strengthening and Toughening of ZG25SiMn2CrB Steel without Tempering Brittleness via Electropulsing Treatment

Dynamic Magnetostrictive Behavior of Ferromagnetic Metal

Effect of alternating magnetic field on microstructure evolution and mechanical properties of M50 bearing steel during tempering process

Effect of Pulsed Magnetic Field on Retained Austenite of Quenched 8cr4mo4v Steel under Cryogenic Condition

Effect of Pulsed Magnetic Field on the Microstructure of TC4 Titanium Alloy and Its Mechanism

Enhanced Low Cycle Fatigue Properties of Ti-6Al-4V Alloy by Post-treatment Technology of Pulse High-Intensity Magnetic Field

Reducing Residual Stresses in Engineering Structures by Pulsed Magnetic Treatments

Effect of Laser Quenching-Shock Peening Strengthening on the Microstructure and Mechanical Properties of Cr12MoV Steel