Abstract:s The paper uses a laser cladding process to prepare a composite coating of Ni60A and x% TiC (x = 0, 2, 4, 8) by mass percentage on the surface of H13 steel. The effects of different TiC additions on the microstructure and properties of the laser cladding coatings were analyzed by X-ray diffractometer (XRD), non-destructive testing, Penetrant testing (PT), optical microscope (OM), scanning electron microscope (SEM), energy dispersive spectrometer (EDS), micro-hardness tester, friction and wear tester, and electrochemical workstation. The results show that the coating microstructure without TiC addition was dominated by dendrites. The microstructure of the coatings appeared as short rods and equiaxed crystals after the addition of TiC. After analysis, hard reinforcing phases such as Cr 23 C 6 , Cr 7 C 3 , and TiCx were found to have a pinning effect at the grain boundaries, thus hindering the grain boundary slip. These can significantly increase the hardness of the coating. Most of the Ni60A coating with the addition of 2 wt% TiC (C2)coating curve is at the bottom end of the graph line. It has an average friction factor of 1.43 and a low wear weight loss. C2 coatings have less wear than C0 coatings.C2 coatings have 8.5% of the wear of C0 coatings.C2 has the best wear resistance. The hardness of the C2 coating is 662HV0.5, which is higher than other coatings with different TiC additions. The C2 coating had the lowest self-corrosion current of 7.076 ×10–7 A·cm-2. C2 coatings significantly appear grain refinement, lattice distortion, coating hardness, and wear resistance are high, with better corrosion resistance. The strengthening mechanism is mainly solid solution strengthening and fine grain strengthening together.

Influence of Carbon Content on the Mechanical Properties of TiCN–Cu Nanocomposite Coatings Prepared by Multi-Arc Ion Plating

Influence of Carbon Contents on the Structure and Tribocorrosion Properties of Tisicn Coatings on Ti6al4v

Effects of C content on the microstructure, mechanical and tribological properties of TiAlSiCN coatings

Preparation and Tribological Properties of the Carbon Nanotubes–ni–p Composite Coating

Structure and Tribological Properties of CrTiAlCN Coatings with Various Carbon Contents

Effect of Cu doping on the microstructure and mechanical properties of AlTiVN-Cu nanocomposite coatings

Influence on (Ni-P) Electroless Composite Plating with Carbon Nanotubes

Influence of Cu Content Variation on the Tribological Properties of Ni60CuMo with Sandwich-Structured Composite Coatings by Laser Cladding

Carbon Nanotubes Improves the Tribological Properties of Ni60/Al<sub>2</sub>O<sub>3</sub> Coatings

Tribological properties of Ni–P-multi-walled carbon nanotubes electroless composite coating

Influence of C2H2/N2 flow ratio on the microstructure, mechanical properties, and electrochemical behavior of TiCN composite coatings

Microstructure, mechanical properties and high-speed dry-cutting performance of AlCrSiCN composite coatings

Microstructure and mechanical properties of Ti–Si–C–N coatings deposited by hybrid arc enhanced magnetron sputtering

Influence of Cu Content on the Microstructure and Mechanical Properties of Cr-Cu-N Coatings

EFFECT OF THE N2/Ar FLOW RATIO ON THE MICROSTRUCTURE AND MECHANICAL PROPERTIES OF TiSiCN COATINGS

Effect of carbon content on the tribological behaviour of TiC x coatings prepared by reactive HiPIMS

Effect of C doping on structure and properties of TiAlCrN coatings by filter cathode vacuum arc deposition

Microstructure and Tribological Behavior of Cr-Cu-N Coatings Deposited by Ion Beam Assisted Magnetron Sputtering

Tribological Application of Carbon Nanotubes in a Metal-Based Composite Coating and Composites

Effect of TiC addition on the microstructure and properties of laser cladding Ni60A coatings on H13 steel surface

Microstructure and mechanical properties of nanomultilayered AlTiN/Cu coatings prepared by a hybrid system of AIP and PDCMS