Abstract:The KSTAR device is a tokamak with a fully superconducting (SC) magnet system, which enables an advanced quasi-steady-state operation. Initial operation of the KSTAR SC magnet system has been accomplished for the first plasma discharge operation. The SC magnet system consists of 16 toroidal field (TF) coils and 14 PF coils, magnetic structures, SC buslines, current leads, and monitoring and protection system. One of the uniqueness of the KSTAR device is using the Nb3Sn superconductor both in 16 TF coils and in 10 PF coils except 4 PF coils made of NbTi. The objectives of the commissioning of the superconducting magnet are to verify the engineering reliability of all the superconducting magnets at the operating conditions and to develop the operational controllability for the successful plasma startup. The target parameters of the initial operation are TF coil current of 15 kA, PF coil current up to 4 kA and PF blip and feedback control using plasma control system (PCS). All the superconducting magnets were operated reliable without any severe failure to preventing the first plasma operational target. The TF magnet was operated reliably up to 15 kA for 8 hours and the temperature rising of TF magnet is less than 0.1 K. There was no quench during operation including slow and fast discharges. As the PF commissioning, the controllability of each power supply has been tested by using dummy copper load and each SC PF coil. After the individual test of the PF coil and power supply, integrated control was accomplished for the field null formation and for loop voltage generation to meet the first plasma discharge. The ac losses of the several PF coils have been measured by applying the single trapezoidal current and dc biased sinusoidal current with various ramp rate. The hysteresis loss of PF1 coil was less than 180 mJ/cc and the time constant of the coupling loss was less than 50 ms after 500 pulse operations. The field distortion by the Incoloy908 material in the superconductor was measured and modification in the PF coil current scenario has been adopted also. By the feedback control of the plasma current and position, the plasma current could be sustained up to 860 ms under the limited volt second of 1.1 Wb. FIG. 1. Configuration of the KSTAR superconducting magnet system FIG. 2. Bird eye view of the KSTAR superconducting magnet system

Effect of Flow Imbalance on the Operational Performance of the KSTAR PF1UL Magnets

Dynamic Simulation on Flow Characteristics of KSTAR PF Magnet Cryogenic Network

Thermohydraulic Behaviors of Kstar Pf Superconducting Magnet System in Operation

Operating Temperature Margin and Heat Load in PF Superconducting Coils of KSTAR

Hydraulics of KSTAR Central Solenoid Model Coil 2nd Campaign

Pressure Drop of CICC from Manufacturing Stage to Plasma Operation in KSTAR Superconducting Magnet System

Thermohydraulic Characteristics of KSTAR Magnet System Using ITER-like Superconductors

AC Loss Analysis on the KSTAR PF1L Coil Based on the Long-Term Commissioning Shot Data

Qualification Test Results of the KSTAR Superconducting Coils from the Construction to the Commissioning Steps

Review of the Structural Behavior of the KSTAR TF Magnet

Analysis of the Structural Behavior of the KSTAR TF Magnet for Safe Operation

1 FT / P 3-1 Commissioning Results of the KSTAR Cryogenic System

Structural Behavior of KSTAR CS Magnet During Plasma Operation

Prediction of Mechanical Behavior of the KSTAR CS Magnet Based on PF Coil Currents

Numerical Study on the Flow and Heat Transfer Characteristics in CFETR Cryostat During a Loss of Vacuum

Commissioning Results of the KSTAR Superconducting Magnet System for the First Plasma Operation

Experimental Investigation on Liquid-Metal Flow Distribution in Insulating Manifold under Uniform Magnetic Field

Numerical Investigation of Quench Event in the Innermost Pair of the KSTAR Central Solenoids

Experimental Evaluation of the Influence of External Current on the Kstar Tf Quench Detection System

First Commissioning Results of the KSTAR Cryogenic System

KSTAR Magnetic Field Measurement During the Commissioning and Remanent Field Evaluation