Abstract:The stiffness of machine tools is a key factor to increase the productivity. The dynamic stiffness dominates the stable cutting conditions, where forced and regenerative chatters do not occur. In general, dynamic stiffness is measured using an impact hammer as it does not require the particular device setting. However, humans should use a hammer and impact control needs skills. To this end, several researches have been conducted to establish automatic excitation methods. To measure the dynamic stiffness of a rotating spindle, authors have developed an electromagnetic biaxial excitation device which can generate biaxial force. This paper presents the measurement result of dynamic stiffness for both the structure and spindle of a five-axis machining center using the developed device. INTRODUCTION For the avoidance of chatter vibrations in machining, chatter mechanism and suppression methods have been studied [1]. One of the well-known techniques is chatter prediction using stability limit diagrams (SLDs), where the relation between the limit of depth of cut and spindle speed is analyzed and shown graphically. For the prediction of the stability limit accurately, it is necessary to measure the precise dynamic compliance of the machine. In general, dynamic stiffness is measured using an impact hammer for its simplicity. However, humans should use a hammer with skills. To this end, several researches have been conducted to establish automatic excitation methods [2-4], which are categorized into contact and contact-less methods. The noncontact excitation method has been developed to analyze the dynamics of rotating spindle. It also can explain the dynamics of machine structure comparably. This paper presents the analysis of both the structure and spindle of a five-axis machining center using the developed device. Through the measurement tests, anisotropic in stiffness were investigated. MEASUREMENT SYSTEM Figure 1 (a) shows the schematic of a developed biaxial electromagnetic excitation device [5]. The device consists of iron cores, coils, yoke (housing) and its cross-section view is shown in Fig. 1 (b). A dummy tool attached to the spindle is inserted into the hole, facing to the coils with air-gap. Giving current to two coils generate magnetic flux, flown to the surface of the dummy tool and the yoke. Thus, two coils can produce a single attraction fore in a single direction. Eight coils generate biaxial force (x and y) in plus and minus directions. Yoke diameter:φ220 mm Hight : 160 mm (a) Isometric view (b) Sectional view Figure 1: Schematic of electromagnetic excitation device. Figure 2 shows the experiment and measurement system. The excitation device was installed on the machine tool table of a five-axis machining center, where a dynamometer was placed on the table to measure attractive forces. The dummy tool that integrates a holder interface was attached to the spindle. Displacement sensors were installed at the upper case of the housing, measuring the holder displacement of the dummy tool in the xand the y-directions. A control PC sent a swept-sine current command to an amplifier that gives coil current to Coil Housing Iron core 22.5° 22.5°

CONTACTLESS MEASUREMENT OF SPINDLE STIFFNESS BY USING LATERAL STATOR MAGNETIC LOADER

Study of Differential Magnet-moving Type Velocity Sensor

Measurement of Dynamic Performances of High-Speed Rotating Spindle by Non-Contact Electromagnetic Loading Device

Analysis on the stiffness of angular contact ball bearings and its effect on the critical speed of a high speed motorized spindle

A novel approach for preload measurement and analysis of fixed position preload spindle

Stiffness Modeling, Identification, and Measuring of a Rotating Spindle

Magnetomechanical Measurements for Nondestructive Evaluation of Failure in Steel Structural Element

Test Verification for Improved Design of Rotor Blade by ESPI

Investigation of machine tool rigidity through measurements and FEA

Sensorless Control Strategy of Novel Axially Magnetized Vernier Permanent-Magnet Machine

Identification of Laminated Core and Winding's Physical Parameters by Stator's Modal Testings

INVESTIGATION OF DYNAMIC STIFFNESS OF MACHINE TOOL WITH ELECTROMAGNETIC BIAXIAL EXCITATION DEVICE

Modelling and testing of the dynamic support stiffness of assembled bearings in motorized spindles

High-speed tooth-coil permanent magnet synchronous machine for motorized spindle application

Design to reduce electromagnetic vibration in integral-slot SPM machine considering force modulation effect

Characteristics of stiffness and contact stress distribution of a spindle-holder taper joint under clamping and centrifugal forces

Flux Density Measurement of Radial Magnetic Bearing with a Rotating Rotor Based on Fiber Bragg Grating-Giant Magnetostrictive Material Sensors.

Design and Research of New Type High-speed Hydrostatic Spindle Test Rig

Investigation of spindle-tool assembly dynamics for optical grinding motorized spindles

Multi-dimensional force tracking-loading simulator development and simulation experiment for five-axis machining center

Comparison of Two Auxiliary Suspension Winding Configurations for High-Speed SPMSM with Aerodynamic Bearings