Abstract:Driven by the rapidly-growing of hybrid and electric vehicles, there is an increasing demand on lithium ion batteries (LIBs) with high energy density, long cycle life, and low cost. One of the most widely used anode materials in LIBs, graphite, only possesses a theoretical specific capacity of about 370 mAh/g, limiting the specific energy of LIBs.1 Recently, conversion-type of electrode materials, i.e. metal oxide and metal sulfide, has been regarded as one of the most promising anode materials for high performance LIBs, due to the low cost and exceptionally high specific capacity (>1000 mAh/g).2 However, these conversion-type electrode materials suffers from several issues, i.e. relatively low conductivity and rapid capacity fade due to irreversible phase change and particle pulverization during cycling. For example, the poor performance of tin oxide is mainly caused by its low intrinsic conductivity, formation of irreversible insulating Li2O phase during discharging, and large volume change.3 To overcome these disadvantages, various methods have been developed, like carbon/tin oxide composites, tin phosphide (Sn4P3). Tin phosphide has a layered structure and can be prepared by a mechanochemical or hydrothermal method. It has shown promising electrochemical performance as the anode in Li-ion batteries.4,5 As the lithium was inserted, Sn4P3 was first converted into lithium phosphides and Sn, followed by lithium-tin alloy formation. The advantage of Sn4P3 is its high capacity and Li+ conductivity of the Li3P. However, it suffers from similar drawbacks as tin oxide, i.e. large volume change and irreversible Li3P phase formation. In this work, we prepared Sn4P3 nanowires by hydrothermal reaction of red phosphorus and tin in ethylenediamine at 200 °C for 40 h. Then, graphite/Sn4P3 composites were prepared by high-energy ball milling for 2 h under Ar atmosphere. Graphite and Sn4P3 were uniformly distributed in the composites, shown in Figure 1a. When tested as the anode materials, the composites showed superior performance compared to Sn4P3 alone. The capacity of Sn4P3 rapidly decreased to around 200 mAh/g after 15 cycles. In comparison, graphite/Sn4P3 composites showed an initial specific capacity of about 1014 mAh/g and maintained a capacity of 782 mAh/g after 50 cycles. In addition, the coulombic efficiency was also much higher in the graphite/Sn4P3 composites, indicating a reversible Li insertion/deinsertion behavior and more stable SEI layer. The rate performance of graphite/Sn4P3 composites was also much better than pure Sn4P3. In conclusion, we report a facile preparation of graphite/Sn4P3 composites with excellent electrochemical performance as anode material in Li-ion batteries. Figure 1

Phosphorus-rich Tin Phosphide-Carbon Nanotubes Composite As a High-Performance Anode for Potassium Ion Batteries

A high-performance tin phosphide/carbon composite anode for lithium-ion batteries

Multi-geometric carbon encapsulated SnP3 composite for superior lithium/potassium ion batteries

Enhanced Silicon Diphosphide-Carbon Composite Anode for Long-Cycle, High-Efficient Sodium Ion Batteries

Rational design of Sn 4 P 3 /Ti 3 C 2 T x composite anode with enhanced performance for potassium-ion battery

Sn/P@G-CNTs Composites As High-Performance Anode Materials for Sodium-Ion Batteries

Enhancing the Cycling Stability by Tuning the Chemical Bonding between Phosphorus and Carbon Nanotubes for Potassium-Ion Battery Anodes

Rational design of Sn4P3/Ti3C2Tx composite anode with enhanced performance for potassium-ion battery

Investigation of Graphite/Tin Phosphide Composites As the Potential Anode in Li-Ion Batteries

Few-Layered Tin Sulfide Nanosheets Supported on Reduced Graphene Oxide As a High-Performance Anode for Potassium-Ion Batteries

Enhanced Capacity of Chemically Bonded Phosphorus/carbon Composite As an Anode Material for Potassium-Ion Batteries

Phosphorus-Based Alloy Materials For Advanced Potassium-Ion Battery Anode

Encapsulation of CoS 2 nanoparticles in bamboo-like carbon nanotubes as advanced potassium-ion batteries anodes

Structure‐Optimized Phosphorene for Super‐Stable Potassium Storage

Tin phosphide nanoparticles loaded on multi-walled carbon nanotubes networks as a superior anode material for lithium ion batteries

Antimony/Polypyrrole/CNTs composites with three-dimensional structure as highly stable anodes for potassium ion battery

Hierarchically Porous Carbon Supported Sn4P3 As a Superior Anode Material for Potassium-Ion Batteries

Constructing Tin Sulfide Nanosheets Embedded in N-doped Graphene Frameworks for Potassium-Ion Storage

Metastable trigonal SnP: A promising anode material for potassium-ion battery

Fe2P nanoparticles-doped carbon nanofibers with enhanced electrons transfer capability as a self-supporting anode for potassium-ion battery

SnP entangled by carbon nanotube networks as anode for pseudocapacitive half/full battery