Abstract:Polymer-based thermal conductive composites (PTCs) with both excellent thermal and mechanical properties are highly desirable in the thermal management of modern microelectronic industry. However, the enhancement efficiency for fillers loaded polymer composite is actually lower than the theoretically predicted value. The significant reasons could be due to the restriction of interfacial thermal resistance at filler-polymer matrix interfaces as well as the thermal conductive orientation dependence of anisotropic fillers. In the present study, solid-state shear milling (S3M) strategy and FDM 3D-printing aligning technology were combined to synergistically improve thermal conductivity of linear low-density polyethylene (LLDPE)/graphene nanoplatelet (GNPs) nanocomposites. The fabricated FDM 3D-printed parts exhibit a significantly enhanced through-plane thermal conductivity up to 3.43 W m−1 K−1 along printing direction compared to that of neat LLDPE (0.40 W m−1 K−1) and also that of traditionally melt-compounded LLDPE/GNPs composites (1.98 W m−1 K−1) at the same GNPs loading of 15.0 vol%. The enhanced thermal conductivity is attributed to the long-range aligned bridge-connected network structure of GNPs constructed in the PE matrix along printing direction due to the shear-inducing effect of FDM 3D-printing. Simultaneously, the S3M technology we adopted also reduces the interfacial thermal resistance and thus increases the thermal conductivity of the obtained nanocomposite, which was further demonstrated by the way of theoretical effective medium approximation (EMA) models we applied. The achieved high thermal conductivity and mechanical properties of the FDM 3D-printed LLDPE/GNPs thermal conductive parts suggest promising applications in the heat diffusion of some advanced electronic devices.

A Rapid and Simple Method to Draw Polyethylene Nanofibers with Enhanced Thermal Conductivity

Thermal Conductivity of Individual Electrospun Polymer Nanofibers

Experimental Research on Thermo-Direct Fiber Drawing Technique

High Thermal Conductivity of Polyethylene Nanowire Arrays Fabricated by an Improved Nanoporous Template Wetting Technique

Novel Polyethylene Fibers of Very High Thermal Conductivity Enabled by Amorphous Restructuring.

Thermal Conductivity of Electrospinning Chain-Aligned Polyethylene Oxide (PEO)

Microstructure and Mechanical Properties of Hot-Air Drawn Poly(ethylene-2,6-naphthalate) Fibers

Experimental Study of Thermal Conductivity of Polyethylene Nanowire Arrays Fabricated by the Nanoporous Template Wetting Technique

Preparation of High-Modulus Poly(ethylene Terephthalate) Fibers by Vibrating Hot Drawing

Covalently linked polydopamine-modified boron nitride nanosheets/polyimide composite fibers with enhanced heat diffusion and mechanical behaviors

Enhanced Thermoelectric Properties of Bi2 Te3 -Based Micro-Nano Fibers Via Thermal Drawing and Interfacial Engineering.

Excellent thermal conductive epoxy composites via adding UHMWPE fiber obtained by hot drawing method

Enhancing thermal conductivity of bulk polyethylene along two directions by paved crosswise laminate

Enhanced Thermoelectric Properties of Bi2Te3‐based Micro‐nano Fibers Via Thermal Drawing and Interfacial Engineering

Polymer Composite with Enhanced Thermal Conductivity and Insulation Properties through Aligned Al2O3 Fiber

Carbon nanothreads enable remarkable enhancement in the thermal conductivity of polyethylene

Extremely High Thermal Conductivity of Aligned Bulk Carbon Nanotube-Polyethylene Composites

Fabrication of Polyethylene Nanofibrous Membranes by Biaxial Stretching

Influencing Factors and Measuring Method of the Heat Conducting Performance of UHMWPE Single Fiber

Facile and scalable fabrication of highly thermal conductive polyethylene/graphene nanocomposites by combining solid-state shear milling and FDM 3D-printing aligning methods

Porous polyetherimide fiber fabricated by a facile micro-extrusion foaming for high temperature thermal insulation