Abstract:Preparation of the low‐velocity and tension‐after‐impact testing specimens and damage mechanism observed on the z‐pin reinforced curved composites. This paper studies the influence of z‐pins on the impact resistance and residual tensile properties of composite large curvature components through low‐velocity impact and tension‐after‐impact tests to explore the damage mechanism. Unpinned and z‐pinned specimens with different diameters (0.3 and 0.5 mm) and spacing (3, 4, and 5 mm) were impacted at energies of 28 J and 14 J + 14 J and were stretched until failure. The theoretical models were used to predict impact dent depth and tensile strength, and the effectiveness of z‐pins and damage patterns were characterized by force‐time/displacement curves and through visual observation. The agreement between the experiments and predictions can thus validate the presented approach. Through the low‐velocity impact test, it is found that z‐pins with higher density and smaller diameter make the impact dent shallower and the surface damage less, thus showing better performance. Later, the impacted specimens mainly show delamination, explosion, breakage, and splitting after tension. During the first stage of the force‐displacement curves, since z‐pins mitigate the delamination, tensile strength shows a 29.58%–59.17% increase while in the third stage, a decrease of 3.95%–15.12% occurs due to initial damage caused by z‐pins. Highlights Different impact energies are implemented on large curved CFRP laminates of z‐pins with different diameters and spacing to explore the damage mechanism. Low‐velocity impact and tension‐after‐impact (TAI) tests are used to simulate the centrifugal force of the blade subjected to impact and rotation after impact. Z‐pinned group with a small diameter and high density causes less damage and tensile strength in the first stage increases while decreasing in the third stage compared with the unpinned group.

Bridge Effects Of Z-Pin On Damage Evolution Of Z-Pin Reinforced Composite T-Joint: Experiment And Simulation

Strengthening of Composite T-joints Using Ø 0.11 Mm Z-pins Via an Ultrasound-Guided Insertion Process

Experimental Study and Numerical Analysis of A Composite Bridge Structure

Effect of Ø 0.11 Mm Z-pinning on the Properties of Composite Laminates Via an Ultrasound Guided Insertion Process

Minimizing the In-Plane Damage of Z-pinned Composite Laminates Via a Pre-Hole Pin Insertion Process

Micro-damage Initiation Evaluation of Z-Pinned Laminates Based on a New Three-Dimension RVE Model

Concurrent Multiscale Modeling of In-Plane Micro-Damage Evaluation in Z-pinned Composite Laminates

A Novel Model of Z-pin Insertion in Prepreg Based on Fracture Mechanics

Out-of-plane Properties and Failure Mechanism of Composite Laminates Reinforced with Carbon Z-pins

Experimental Investigation of Z-pin Insertion Angles on the Mechanical Behavior and Failure Mechanism of Compression after Impact for CFRP Laminates

Effect of Z-pin Insertion Angles on Low-Velocity Impact Mechanical Response and Damage Mechanism of CFRP Laminates with Different Layups

Experimental investigations into damage mechanism in the low‐velocity impact and tension‐after‐impact testing of z‐pin reinforced curved CFRP composite

Effect of fine metallic Z-pin on compressive property of open-hole composite laminate

Delamination bridging response of Z‐pins under mixed mode loading: The influence of carbon and Kevlar Z‐pins

Progressive failure analysis of z-pin reinforced composite pi joints

Using z-pinning to improve the low-velocity impact performance of composite skin/stringer structures

Enhancement of Composite Open-Hole Tensile Strength Via Fine Z-pins Arrangements

A Finite Element Model for Predicting the Static Strength of a Composite Hybrid Joint with Reinforcement Pins

Influence of Z‐pin material on the mechanical properties of fine Z‐pin reinforced composites

A model for the response of unreinforced and Z-pin reinforced composite Pi joints

Effect of Z-pin inclined angle on the impact damage suppression effectiveness for cross-ply composite laminates