Abstract:Steam Generator (SG) is a critical equipment in the nuclear power plant, it is the huge heat exchanger in reactor system which can achieve removing fission energy from the reactor system effectively to ensure safety of the whole nuclear system. It is located between the primary and the secondary loop in reactor system act as the intermediate hub of energy and the security barrier in nuclear power plant. Generally, there are numerous of U-shaped heat transfer tubes in SG it is one of the weakest structures throughout the primary loop system. So the integrity of the SG especially its heat transfer tubes is important to the safety of reactor operation. The degradation problem of heat transfer tubes together with ruptures accidents often occur under suffer environments in reactors, which include thermal stress, mechanical stress and so on, it is noteworthy that this kind of accidents is inevitable due to the limited properties of existing materials. The performance of the SG is seriously affected by the number of failure tubes. Plugging operations through various mechanical means is the most common method to solve the tubes ruptures problems which can reduce the economic losses to the utmost extent. However, plugging operations will make huge impact on the thermal hydraulic performances of both sides of SG. It’s meaningful to research the characteristics of the plugging affects under different operations. In this paper the hydraulic characteristics of primary side in AP1000 SG under a certain fraction of heat transfer tube plugging conditions is researched. Three dimensional hydraulic characteristics of primary side coolant in SG under different plugging conditions are obtained by using the thermal hydraulic software FLUENT. The typical plugging fraction in this simulation model is 10 percent, and the effect of plugging locations also be considered through changing the plugging positions using the zone marking method. The results shows that the pressure drop under the structure integrated SG is 358.01MPa which is accordance with the results from Westinghouse 343KPa. The pressure drop values varies when changing positions of the plugging tubes under the same plugging fraction condition. The flow fields in bottom head also change meanwhile and the maximum pressure drop can reach up to 388.05KPa when the plugging fraction is 10%. The growth rate become significant when tube plugging fraction larger than 5%, and differences between maximum and minimum values of total pressure drop under different plugging positions become larger gradually. Finally the local resistance coefficients and flow field distributions of primary side in SG under various plugging conditions are obtained which is meaningful for the reactor safety and it can be a good reference for the maintenance of SG.

Cfd Simulation Of Thermal-Hydraulic Characteristics Of Water Seal Structure In Pwr Pressurizer

Study on the Water Seal Formation Process in Advanced PWR Pressurizer Using CFD Method

Experimental Investigation on Hot Water Seal over an Analogous U-shaped Device

Experimental Investigation on Analogous U-Shaped Tube Water Seal in Front of Pressurizer Safety Valve

CFD simulation of thermal hydraulic phenomena in enclosed cavity of nuclear power plants

Development of CFD Methodology for Investigating Thermal-Hydraulic Characteristics in a PWR Dome

Numerical Investigation on the Thermal Stratification in a Pressurizer Surge Line

A Thermohydrodynamic Analysis of Dry Gas Seals for High-Temperature Gas-Cooled Reactor

Multi-scale Thermal-Hydraulics Analysis on SCWR Fuel Qualification Test Loop

CFD Investigation on Thermal Hydraulics of the Passive Residual Heat Removal Heat Exchanger (PRHR HX)

Hydraulic Characteristics Research on SG under Tube Plugging Operations Using FLUENT

Three dimensional thermal hydraulic coupling method on pwr steam generator using cfd method

CFD Simulation of Thermal Hydraulic Characteristics in a Typical Upper Plenum of RPV

Thermal Performances of the Wave-Tilt-dam Seal in a Reactor Coolant Pump for Sustainable Development

Experimental Research on the Characteristics of Steam-Water Counter-Current Flow in the Pressurizer Surge Line Assembly

Numerical Simulation of Micro-Crack Leakage on Steam Generator Heat Transfer Tube

Thermal-Hydraulic Analysis For Experimental Device Of Supercritical Water Reactor-Fuel Qualification Test

Thermal-fluid-structure Analysis of Fast Pressure Relief Valve under Severe Nuclear Accident

Experimental study on pressure fluctuation in header of nuclear power plant SEC system after long-term pump shutdown

Influence of structural parameters on wavy-tilt-dam hydrodynamic mechanical seal performance in reactor coolant pump

Fluid-solid Strong-Interaction Model of Mechanical Seals in Reactor Coolant Pumps