DC-SRF Photocathode Gun
Senlin Huang,Kexin Liu,Kui Zhao,Jiaer Chen
DOI: https://doi.org/10.1360/tb-2022-1091
2022-01-01
Chinese Science Bulletin (Chinese Version)
Abstract:The DC-SRF photocathode gun, an important member of superconducting radio-frequency (SRF) guns, is a distinguished compact mega-electron-volt (MeV) electron source capable of generating picosecond to sub-picosecond electron pulses at megahertz (MHz) and higher repetition rate. The concept of DC-SRF was conceived by the SRF Accelerator Laboratory of Peking University in 2001, which combines a DC gap and a 1.3 gigahertz (GHz) SRF cavity connected by a short drift tube around 10 mm long. By introducing the DC gap, the semiconductor photocathode is moved out from the SRF cavity, which successfully solves the compatibility problem between the photocathode and the SRF cavity as validated by later experiments. Besides, the high vacuum in the cryogenic DC structure allows the usage of green laser photocathodes, which benefits the generation of high repetition rate, high average current electron beams. The development of the DC-SRF photocathode gun has so far undergone three stages: The prototype, DC-SRF-I, and DC-SRF-II. The feasibility of the DC-SRF concept was first tested in 2004 with the prototype employing a 1.5-cell SRF cavity and operated at pulsed mode under 4.2-4.4 K. In the following decade, the first-generation DC-SRF gun, DC-SRF-I, was developed with the purpose to deliver electron beams for research on infrared (IR) FEL, energy recovery linac, terahertz (THz) radiation, etc, and for a higher energy gain, it employed a 3.5-cell SRF cavity. The DC-SRF-I gun was brought into stable operation in 2014 with a DC voltage of 45-50 kV, an SRF cavity gradient of 7-9 MV/m (corresponding to an energy gain around 3 MeV), and a dark current evaluated to be lower than 1 nA. It is the first SRF gun that can operate steadily with semiconductor photocathodes. The MHz repetition rate electron beam from the DC-SRF-I gun had been used for applications including high repetition rate superradiant THz undulator radiation, ultrafast electron diffraction, etc. In 2015, the electron beam was injected into a 2x9-cell SRF linac and the energy was boosted to 10-20 MeV. Until DC-SRF-I's shutdown in 2016, no degradation of the SRF cavity had been observed. The design and the manufacturing technology, however, had imposed limits on the improvement of DC-SRF-I's performance. With the goals to achieve low-emittance CW operation and to generate high average current electron beam, the development of the second-generation DC-SRF gun, DC-SRF-II, was started in 2016. The physics design was accomplished in 2017, in which the DC voltage is increased to 100 kV and a 1.5-cell SRF cavity is adopted with an expected gradient of 13-14 MV/m. K2CsSb photocathode is used in combination with temporal and spatial shaping of the drive laser. The beam optics is also carefully designed for optimized emittance compensation. Simulation indicates that a normalized emittance of 0.33 mm-mrad can be achieved at a bunch charge of 100 pC with the above measures. Based on the experiences with DC-SRF-I and the SRF linacs developed by the Laboratory, the engineering design and fabrication of DC-SRF-II have been greatly improved. Especially, a TTF3-type RF power coupler with enhanced cooling has been employed, allowing CW operation of DC-SRF-II with a maximum average current up to 10 mA. DC-SRF-II was built in 2021. It has succeeded in CW operation with a bunch charge of 100 pC and a repetition rate of 1 MHz. The dark current of the gun is below 1 pA and the normalized emittance of the delivered electron beam is at sub-mm-mrad level. These indicate a leading performance among the SRF guns worldwide.