Abstract:To reduce the deformation and improve the quality of thin-walled parts repaired by laser cladding, a three-factor, three-level orthogonal experimental scheme was employed to clad Ni60 powder on thin-walled parts with a thickness of 3.5 mm. To measure the deformation of the thin-walled parts, a method of combining the meshing of the backs of the thin-walled parts and fixing one end of the parts during cladding was used. The effects of the powder feed rate, laser power, and scanning speed on the deformation of the thin-walled parts were studied via visual analysis and analysis of variance, and the process parameters that resulted in the minimum deformation were determined. The deformation process of the thin-walled parts and the causes of cladding stress were also studied, and the microstructure of the cladding layer with the minimum deformation was analyzed via scanning electron microscopy (SEM). The results reveal that the deformation of the thin-walled parts increased with the increase of laser power. The increases of the scanning speed and powder feed rate were found to reduce the deformation of thin-walled parts; the laser power was found to have a significant effect, and the powder feed rate was found to have no significant effect, on the deformation of thin-walled parts. The order of the influence of factors on the deformation of thin-walled parts from greatest to least was determined to be as follows: laser power > scanning speed > powder feed rate. The optimal parameters to obtain the minimum deformation and good metallurgical bonding of thin-walled parts were found to be a powder feed rate of 1.4 r/min, a laser power of 1100 W, and a scanning speed of 8 mm/s. From the bottom to the top, the crystal structure of the coating with the minimum deformation was found to be coarse dendrite, dendritic crystal, and equiaxed crystal.

Laser Cladding Additive Manufacturing Of Fully Dense Metal Components And Investigations Of Cracking Control Technology

Microstructure and Mechanical Properties of Ti-6al-4v Components Fabricated by Laser Micro Cladding Deposition

An Overview of Laser Metal Deposition for Cladding: Defect Formation Mechanisms, Defect Suppression Methods and Performance Improvements of Laser-Cladded Layers

Laser Surface Cladding: the State of the Art and Challenges

Dynamic evolution behavior of cracks for single-track and multi-track clads in laser cladding

Hot Crack Formation Mechanism and Inhibition of a Novel Cobalt-Based Alloy Coating during Laser Cladding

Effect of Laser Scanning and Powder Addition on Microstructure and Mechanical Properties for Hot-Wire-Feed Laser Additive Manufacturing

Development of microstructure simulation methods of laser cladding layer

Quantitative analysis and experimental study of the influence of process parameters on the evolution of laser cladding

A review on cracking mechanism and suppression strategy of nickel-based superalloys during laser cladding

Crack Formation Mechanisms and Control Methods of Laser Cladding Coatings: A Review

Thermomechanical Process Simulation and Experimental Verification for Laser Additive Manufacturing of Inconel®718.

Mechanical properties and microstructure of laser-cladding additively manufactured 316L stainless steel sheets

The study of hot deformation on laser cladding remanufactured 316L stainless steel

Survey of Microstructures and Dimensional Accuracy of Various Microlattice Designs Using Additively Manufactured 718 Superalloy

Status of Research on Assisted Laser Cladding and Laser Cladding Posttreatment: A Review

Laser cladding of aerospace materials

Multicomponent Multiphase Modeling of Dissimilar Laser Cladding Process with High-Speed Steel on Medium Carbon Steel

A Novel Grain Refinement Design to Inhibit Liquation Cracking in Laser Cladding Non-Weldable Nickel-Based Alloy

Research about the Microcrack Mechanisms in Molybdenum and Corresponding Suppression Strategies During Laser Additive Manufacturing Process

Study on the Deformation Control and Microstructures of Thin-Walled Parts Repaired by Laser Cladding