Abstract:Hardening or softening associated with the increase of dislocation density is correlated with strain rate and dislocation density. Taking aluminum as a model material, we investigate the strain rate and dislocation density dependence of the strength and the accompanying hardening or softening effect upon a dislocation increase. This investigation is enabled by employing a newly developed crystal plasticity model, which is validated against the mechanical behaviors in an extremely wide strain rate range, and featured by a parameter-free mobile dislo-cation fraction law based on the exponential distribution of dislocation link lengths and an averaged dislocation velocity model that considers both thermally-activated waiting mechanism and drag-dominated running mechanism. Results show that at different strain rates, the material strength varies with a universal feature that it first softens as the dislocation density increases from a sufficiently low initial value, and then hardens after reaching the minimum strength, where the critical dislocation density separating the softening from hardening regimes increases with the strain rate. Microscopically, the strength dependence on dislocation density and strain rate originates from their influence on the two competing effects of a dislocation increase, where the hardening effect comes from the higher resistance to dislocation slip by increased forest dislocations while the softening effect comes from the larger quantity of mobile dislocations. These two competing effects are quantitatively evaluated by the crystal plasticity model and are further cast into the competition between the partial derivatives of normalized dislocation velocity and of normalized mobile dislocation density, and the governing equation for the critical dislocation density is thus furnished by balancing these two competing effects. Further, a complete map in the entire space of strain rate and dislocation density (epsilon, rho) is constructed for the zones of dislocation hardening or softening, where the zone-boundary curve for critical dislocation density exhibits a two-stage character and it agrees well with the available experimental data. Such a map is expected to help predict the trend for strength evolution under different serving conditions and also guide the material design according to the requirements for strength variation in service.

Cyclic Plasticity Of Aluminum In Large Plastic Strain Ranges

Constitutive Model of Aluminum under Variable-Amplitude Cyclic Loading and Its Application to Buckling-Restrained Braces

Stress–Strain Behaviors in Large Plastic Strain Ranges under Monotonic Loading

Investigation on Plastic Flow Behaviors of FCC Polycrystalline Aluminum under Pre-Cyclic Tension-Compression Loading: Experiments and Crystal Plasticity Modeling.

Constitutive Modeling on Cyclic Stress-Strain Behaviour of 7A04-T6 High-Strength Aluminium Alloy

Integration Algorithm for a Modified Yoshida–Uemori Model to Simulate Cyclic Plasticity in Extremely Large Plastic Strain Ranges Up to Fracture

Plasticity evolution of an aluminum-magnesium alloy under abrupt strain path changes

Study on Constitutive Model of Cyclic Elastoplastic Behavior of 6082-T6 Aluminum Alloy

The Characteristics of Plastic Flow and a Physically-Based Model for 3003 Al–Mn Alloy Upon a Wide Range of Strain Rates and Temperatures

Damage analysis of aluminum alloy gusset joints under cyclic loading based on continuum damage mechanics

Grain-level Statistical Plasticity Analysis on Strain Cycle Fatigue of a FCC Metal

Experiment and Constitutive Modeling on Cyclic Plasticity Behavior of LYP100 under Large Strain Range

Experimental and modeling study of cyclic plasticity and ductile fracture of thin structural steel sheets

Plasticity and ductile fracture modeling of an Al–Si–Mg die-cast alloy

Experimental and numerical investigation on plasticity and fracture behaviors of aluminum alloy 6061-T6 extrusions

Experimental Investigation and FE Analysis on Constitutive Relationship of High Strength Aluminum Alloy under Cyclic Loading

Anisotropic Behavior in Plasticity and Ductile Fracture of an Aluminum Alloy

Elasto-plasticity Constitutive Model for Aerospace Aluminium Alloy in Strain Space

Experimental and Modeling Investigation on Anisotropic Plastic Flow of Metal Plates under Nonproportional Loading Conditions

The Drucker–Prager criterion-based plasticity theory of amorphous alloys under the complex stress states

Strain-rate dependent crystal plasticity model and aluminum softening/ hardening transition