Abstract:Objective Mid-infrared (2-20 mu m) laser has a broad prospect in the applications including molecule spectroscopy, material processing, biomedicine, and basic physics research. Mode-locked all-solid-state laser, optical parametric oscillator or amplifier, and mode-locked fiber laser are some general methods for generating mid-infrared ultrafast laser. In the generation of this laser, the mode-locked fiber laser stands out owing to its advantages of flexible structure, fast heat dissipation, and good beam quality. Currently, diode-pumped Er: ZBLAN fiber has been widely investigated at 2. 8 mu m because of its high gain and efficiency. Researchers from Laval University have realized femtosecond mode-locked pulses at 2. 8 mu m using a nonlinear polarization rotation technique, with a pulse width of 207 fs and a peak power of 3. 5 kW. However, owing to the high nonlinearity of single-mode fiber and the large anomalous dispersion of ZBLAN fiber at 2. 8 mu m, the intracavity soliton tends to split at a low peak power. It is an efficient way to amplify the mode-locked pulses to obtain higher pulse energy and peak power. In this study, we reported a 2.8-mu m Er: ZBLAN fiber soliton self-compression amplifier with a pulse width of 110 fs and a peak power of 151 kW. Methods Based on a generalized nonlinear Schrodinger equation, we numerically simulated the pulse evolution in the fiber amplifier. Influence of the saturation energy on the output pulses was investigated. The pulse evolution process in the fiber was used to explain the soliton-self-compression phenomenon in detail (Fig. 1). Guided by the simulated results, we constructed a 2. 8-mu m Er: ZBLAN fiber amplifier, seeded by a nonlinear polarization rotation (NPR) mode-locked Er: ZBLAN fiber laser ( Fig. 2). The amplified pulses were characterized using a mid-infrared spectrometer (Ocean Optics, SIR5000) and intensity autocorrelator (APE, PulseCheck 150) under different incident pump powers. Results and Discussions Fig. 1 shows the numerical simulation results. The pulse width of the seed pulse is 240 fs, and the peak power is 3. 1 kW. The spectrum gradually broadens as the amplified pulse energy increases from 4 nJ to 17 nJ owing to the self-phase modulation [Fig. 1(a) ]. The amplified pulse is shortened to 124 fs because of the combined effect of the anomalous dispersion and self-phase modulation [Fig. 1( b)]. Slight spectrum red-shift is observed through the soliton self-frequency shift. The soliton splitting due to the excess accumulation of nonlinear phase shift limits the higher pulse energy. Figs. 1(c) and 1(d) show the pulse evolution with the fiber in the time and frequency domains, respectively; the soliton self-compression process is clearly visible. Fig. 3 shows the experimental results of the mode-locked fiber laser. At 54.3 MHz, stable mode-locked pulses with a pulse width of 240 fs and a peak power of 16. 9 kW are obtained. The seed source is connected to the amplifier fiber, and the average power output is measured (Fig. 4). The shortest pulse width after fiber amplification is 110 fs [Fig. 5(a)]. The center wavelength is shifted from 2780 nm to 2809 nm [Fig. 5( b)]. When the pulse energy reaches 16. 6 nJ, the calculated peak power of the output pulse is 151 kW. Pulse splitting is observed as the pump power increases further. Conclusions Herein, we report a high-peak-power Er: ZBLAN fiber amplifier at 2.8 mu m that is seeded by an NPR mode-locked Er: ZBLAN fiber laser with a pulse width of 240 fs and a peak power of 3. 1 kW at 54. 3 MHz. A numerical simulation of the model amplifier based on a generalized nonlinear Schrodinger equation is used to analyze its operation and demonstrate the soliton self-compression process. We experimentally obtain the amplified pulses with a pulse width of 110 fs and a peak power of 151 kW. Our results show that self-compression amplification is a reliable method for producing high-peak-power mid-infrared ultrashort pulses at 2.8 mu m. In future, higher-peakpower pulses are expected from the Er : ZBLAN fiber amplifier through dispersion management and system optimization.

2-MW peak-power pulses from a dispersion-managed fluoride fiber amplifier at 2.8 m

Femtosecond Yb-doped Tapered Fiber Pulse Amplifiers with Peak Power of over Hundred Megawatts

Nearly diffraction-limited picosecond pulse amplification from LMA fluoride fiber at 2.8 μm

Watt-level 2.8 μm ultrashort pulse generation from an all-fiber Er:ZBLAN fiber amplifier

Low repetition rate broadband high energy and peak power nanosecond pulsed Yb-doped fiber amplifier

2.8-mu m Er: ZBLAN Fiber Soliton Self-Compression Amplifier

2.3 W, Linearly-Polarized Superfluorescent Generation from a Polarization-Maintaining Er3+-Doped Fluoride Fiber Amplifier Around 2.8 Μm

High Energy and High Peak Power Nanosecond Pulses Generated by Fiber Amplifier

Sub-100 fs pulse generation from dispersion-managed mode-locked Er:ZBLAN fiber laser at 2.8 μm

All-fiber High Energy and Peak Power Broadband Yb-doped Fiber Amplifier

High-energy femtosecond pulse generation from a hybrid mode-locked large-mode-area Er:ZBLAN fiber laser

Old Wavelength, New Performance: Hectowatt 200-μJ-level Femtosecond fiber CPA System at 1064 Nm

Amplification of 1.08 GHz Repetition Rate Femtosecond Laser Pulses to 97 W Average Power by a Fiber Amplifier

Hybrid fiber-single crystal fiber chirped-pulse amplification system emitting more than 1.5 GW peak power with beam quality better than 1.3

High average power and energy microsecond pulse generation from an erbium-doped fluoride fiber MOPA system.

Tunable High Energy Pulse Generation in the Range of 2.9-3.6 Μ M Enabled by an Actively Q Switched Er3+/Dy3+ Codoped Fluoride Fiber Oscillator

Generation of high-power 780 nm femtosecond pulses by an all-polarization-maintaining Er-doped fiber amplification system

414.9 W In-Band Pumped Er/Yb Co-Doped Fiber Amplifier Seeded by a Random Fiber Laser.

Pulse shaping, high average power narrow linewidth Er, Yb co-doped fiber amplifier

2.5 Mj Narrow-Linewidth, Linearly-Polarized Pulse-Burst High-Power Yb-Doped Fiber Amplifier System

Hundreds of picosecond pulses amplifier based on Yb-doped tapered fiber for the generation of 100 W average output power