Abstract:The American Conference of Governmental Industrial hygienists (ACGIH) lowered the threshold limit value (TLV) for respirable crystalline silica (RCS) exposure from 0.05 to 0.025 mg m(-3) in 2006. For a working environment with an airborne dust concentration near this lowered TLV, the sample collected with current standard respirable aerosol samplers might not provide enough RCS for quantitative analysis. Adopting high flow rate sampling devices for respirable dust containing silica may provide a sufficient amount of RCS to be above the limit of quantification even for samples collected for less than full shift. The performances of three high flow rate respirable samplers (CIP10-R, GK2.69, and FSP10) have been evaluated in this study. Eleven different sizes of monodisperse aerosols of ammonium fluorescein were generated with a vibrating orifice aerosol generator in a calm air chamber in order to determine the sampling efficiency of each sampler. Aluminum oxide particles generated by a fluidized bed aerosol generator were used to test (i) the uniformity of a modified calm air chamber, (ii) the effect of loading on the sampling efficiency, and (iii) the performance of dust collection compared to lower flow rate cyclones in common use in the USA (10-mm nylon and Higgins-Dewell cyclones). The coefficient of variation for eight simultaneous samples in the modified calm air chamber ranged from 1.9 to 6.1% for triplicate measures of three different aerosols. The 50% cutoff size ((50)d(ae)) of the high flow rate samplers operated at the flow rates recommended by manufacturers were determined as 4.7, 4.1, and 4.8 microm for CIP10-R, GK2.69, and FSP10, respectively. The mass concentration ratio of the high flow rate samplers to the low flow rate cyclones decreased with decreasing mass median aerodynamic diameter (MMAD) and high flow rate samplers collected more dust than low flow rate samplers by a range of 2-11 times based on gravimetric analysis. Dust loading inside the high flow rate samplers does not appear to affect the particle separation in either FSP10 or GK2.69. The high flow rate samplers overestimated compared to the International Standards Organization/Comité Européen de Normalisation/ACGIH respirable convention [up to 40% at large MMAD (27.5 microm)] and could provide overestimated exposure data with the current flow rates. However, both cyclones appeared to be able to provide relatively unbiased assessments of RCS when their flow rates were adjusted.

Aerosol Analysis Using Handheld Raman Spectrometer: On-site Quantification of Trace Crystalline Silica in Workplace Atmospheres

Analysis of Crystalline Silica Aerosol Using Portable Raman Spectrometry: Feasibility of Near Real-Time Measurement.

An indirect Raman spectroscopy method for the quantitative measurement of respirable crystalline silica collected on filters inside respiratory equipment

Aerosol Analysis Using Quantum Cascade Laser Infrared Spectroscopy: Application to Crystalline Silica Measurement

Measurement of Crystalline Silica Aerosol Using Quantum Cascade Laser–Based Infrared Spectroscopy

Ratiometric SERS Quantification of SO2 Vapor Based on Au@Ag-Au with Raman Reporter As Internal Standard.

Real-time detection of molecular structures and metal components within airborne particles using concurrent Raman and Spark emission spectroscopy

Comparison of the Analysis of Respirable Crystalline Silica in Workplace Air by Direct-on-Filter Methods using X-ray Diffraction and Fourier Transform Infrared Spectroscopy

Toward rapid silica analysis of CPDM samples: Deposition of recovered dust and analysis by FTIR

15 Biomonitoring for Respirable Crystalline Silica: Determination of Si-Containing Particles in Exhaled Breath Condensate Using Single Particle Inductively Coupled Mass Spectrometry

Real-Time Measurement of Airborne Carbon Nanotubes in Workplace Atmospheres.

Benefits and limitations of field-based monitoring approaches for respirable dust and crystalline silica applied in a sandstone quarry

Measuring Respirable Crystalline Silica (Quartz) from Powdery Materials through Sedimentation and X-ray Diffractometry

Application of a Fourier Transform Infrared (FTIR) Principal Component Regression (PCR) Chemometric Method for the Quantification of Respirable Crystalline Silica (Quartz), Kaolinite, and Coal in Coal Mine Dusts from Australia, UK, and South Africa

Lowering reporting limit values for respirable crystalline silica analysis by X-ray diffraction in preparation of the 0.025 mg/m3 occupational exposure limit

A Novel Calibration Method for the Quantification of Respirable Particles in Mining Scenarios Using Fourier Transform Infrared Spectroscopy

Individual Micron-Sized Aerosol Qualitative Analysis-Combined Raman Spectroscopy and Laser-Induced Breakdown Spectroscopy by Optical Trapping in Air.

A temporal evaluation of respirable crystalline silica exposure for construction tasks

A new approach for the determination of silicon in airborne particulate matter using electrothermal atomic absorption spectrometry

Performance of High Flow Rate Samplers for Respirable Particle Collection

Functionalization of Filter Media for Improved Crystalline Silica Analysis Using Raman Spectroscopy