Abstract:Joint-preserving surgical treatment of complex unstable proximal humerus fractures remains challenging, with high failure rates even following state-of-the-art locked plating. Enhancement of implants could help improve outcomes. By overcoming limitations of conventional biomechanical testing, finite element (FE) analysis enables design optimization but requires stringent validation. This study aimed to computationally enhance the design of an existing locking plate to provide superior fixation stability and evaluate the benefit experimentally in a matched-pair fashion. Further aims were the evaluation of instrumentation accuracy and its potential influence on the specimen-specific predictive ability of FE. Screw trajectories of an existing commercial plate were adjusted to reduce the predicted cyclic cut-out failure risk and define the enhanced (EH) implant design based on results of a previous parametric FE study using 19 left proximal humerus models (Set A). Superiority of EH versus the original (OG) design was tested using nine pairs of human proximal humeri ( N = 18, Set B). Specimen-specific CT-based virtual preoperative planning defined osteotomies replicating a complex 3-part fracture and fixation with a locking plate using six screws. Bone specimens were prepared, osteotomized and instrumented according to the preoperative plan via a standardized procedure utilizing 3D-printed guides. Cut-out failure of OG and EH implant designs was compared in paired groups with both FE analysis and cyclic biomechanical testing. The computationally enhanced implant configuration achieved significantly more cycles to cut-out failure compared to the standard OG design ( p < 0.01), confirming the significantly lower peri-implant bone strain predicted by FE for the EH versus OG groups ( p < 0.001). The magnitude of instrumentation inaccuracies was small but had a significant effect on the predicted failure risk ( p < 0.01). The sample-specific FE predictions strongly correlated with the experimental results (R 2 = 0.70) when incorporating instrumentation inaccuracies. These findings demonstrate the power and validity of FE simulations in improving implant designs towards superior fixation stability of proximal humerus fractures. Computational optimization could be performed involving further implant features and help decrease failure rates. The results underline the importance of accurate surgical execution of implant fixations and the need for high consistency in validation studies.

Biomechanical Comparison of Locking and Non-Locking Patient-Specific Mandibular Reconstruction Plate Using Finite Element Analysis.

Biomechanical Behavior of the Three-Dimensionally Printed Surgical Plates for Mandibular Defect Reconstruction: a Finite Element Analysis

Biomechanical Evaluation of Reconstruction Plate for Fixation of Mandibular Prosthesis

Experimental validation of finite element simulation of a new custom-designed fixation plate to treat mandibular angle fracture

Biomechanical assessment of mandibular fracture fixation using finite element analysis validated by polymeric mandible mechanical testing

Biomechanical finite element analysis of short-implant-supported, 3-unit, fixed CAD/CAM prostheses in the posterior mandible

Biomechanical analysis comparing natural and alloplastic temporomandibular joint replacement using a finite element model

Biomechanical Evaluation of Chinese Customized Three-Dimensional Printed Titanium Miniplate in the Lefort I Osteotomy: A Finite Element Analysis

Establishment of Sequential Software Processing for a Biomechanical Model of Mandibular Reconstruction with Custom-Made Plate.

Design And Biomechanical Analysis Of A Novel Mandibular Prosthesis

Biomechanical analysis of mandibular defect reconstruction based on a new base-fixation system

Mandibular reconstruction system reliability analysis using probabilistic finite element method

Influence of bite force and implant elastic modulus on mandibular reconstruction with particulate-cancellous bone marrow grafts healing: An in silico investigation

Biomechanical Evaluation of a Customized 3D-Printed Polyetheretherketone Condylar Prosthesis

Comprehensive biomechanical analysis of three clinically used fixation constructs for posterior malleolar fractures using cadaveric and finite element analysis

Three-dimensional Finite Element Analysis of Mechanical Stress in Symphyseal Fractured Human Mandible Reduced with Miniplates During Mastication

Design and biomechanical evaluation of lateral mandibular prosthesis

[Study of Biomechanical Effects on the Reconstruction of Mandible Defect with Autogenous Bone Grafts].

Locking Plates With Computationally Enhanced Screw Trajectories Provide Superior Biomechanical Fixation Stability of Complex Proximal Humerus Fractures

Design and Biomechanical Evaluation of a Custom Lateral Mandible Titanium Prosthesis

3D-Printed PEEK Implant for Mandibular Defects Repair - a New Method.