Abstract:Background: For large mandibular defects, surgical reconstruction using microvascular fibular grafts has advantages over other alternatives in terms of blood supply and good quality of grafted bone. However, the fibular segment is usually lower in height than that of the original mandible, meaning that the vertical positioning of the fibular graft is variable, with different biomechanical consequences on the reconstructed mandible. Objectives: To use finite element method (FEM) to evaluate stress distribution and displacement of a reconstructed mandible versus an intact mandible under occlusal loads. Methods: A three-dimensional intact edentulous mandibular bone (Model I) and a reconstructed mandible bone with fibular graft were created from CBCT images. Calculation models were generated with fibular bone graft extracted from the reconstructed mandible of identical length placed into a mimicked defect area on the right-hand side of the mandible at three different vertical positions: superior (Model II), intermediate (Model III), and inferior (Model IV). Forces were applied at lower left first molar region and lower left central incisor area. Von Mises stresses and mandibular displacement were calculated as outcome measurements during loadings. Results: Maximum stress and strain within the reconstructed mandible were identified at the posterior border of the graft and the contralateral condyle. Maximum displacement occurred near the interface of fibular graft and anterior segment of the mandible. Stress distribution in the graft under functional loads is much higher than that in the residual mandibular segments from Models II to IV. The combined average maximum stress from anterior and posterior loads is 10.66 times higher in the mandible with inferiorly positioned graft (Model IV), 8.72 times for superior graft (Model II), and 3.68 times for intermediate graft (Model III) than that in the control group (Model I). The worst displacement result during functional loadings was in the group with fibular graft located at the inferior border of the mandible. Conclusions: The position of fibular graft placed in the surgical resection site has significant effects on the mechanical behavior of the reconstructed mandible. The fibular graft aligned with the inferior border of the mandible, the most common site designated location by clinicians, has the worst effects on the stress distribution and displacement to the mandibular under functional loads. The fibular graft placed at the intermediate location has the best biomechanics and provides favorable condition for subsequent prosthetic reconstruction.

Biomechanical Behavior of the Three-Dimensionally Printed Surgical Plates for Mandibular Defect Reconstruction: a Finite Element Analysis

Outcome Evaluation of Three-Dimensionally Printed Patient-Specific Surgical Plates for Mandibular Reconstruction

The use of modified 3D-printed reconstruction plates in mandible segmental defect rehabilitation: a case report

Experimental validation of finite element simulation of a new custom-designed fixation plate to treat mandibular angle fracture

Biomechanical Evaluation of Chinese Customized Three-Dimensional Printed Titanium Miniplate in the Lefort I Osteotomy: A Finite Element Analysis

Three-dimensional Finite-Element Analysis Investigating the Biomechanical Effects of Human Mandibular Reconstruction with Autogenous Bone Grafts

Biomechanical Evaluation of Reconstruction Plate for Fixation of Mandibular Prosthesis

Biomechanical Comparison of Locking and Non-Locking Patient-Specific Mandibular Reconstruction Plate Using Finite Element Analysis.

Biomechanical Analysis of Computer Aided Individualized Functional Reconstruction of Mandible Defect by 3D FEA

The comprehensive on-demand 3D bio-printing for composite reconstruction of mandibular defects

Design And Biomechanical Analysis Of A Novel Mandibular Prosthesis

Establishment of Sequential Software Processing for a Biomechanical Model of Mandibular Reconstruction with Custom-Made Plate.

Clinical application and accuracy analysis of 3D printing guide plate based on polylactic acid in mandible reconstruction with fibula flap

Research on 3D Modeling Technology of Craniofacial Implants Based on Topology Optimization Method

[Three-Dimensional Finite Element Analysis of the Mandible Reconstruction with Fibula].

Finite element analysis and clinical application of 3D-printed Ti alloy implant for the reconstruction of mandibular defects

INDIVIDUALIZED SURGICAL GUIDANCE FOR MANDIBULAR RECONSTRUCTION USING 3D FEA/PRINTING TECHNOLOGIES

Biomechanical analysis of mandibular defect reconstruction based on a new base-fixation system

3D-Printed PEEK Implant for Mandibular Defects Repair - a New Method.

Biomechanical behavior of mandibles reconstructed with fibular grafts at different vertical positions using finite element method

Mechanical properties of three-dimensionally printed titanium plates used in jaw reconstruction: preliminary study