Abstract:Introduction: In recent years, 3-dimensional (3D) printing has been widely used in regenerative medicine research and other fields because of its ability to customize macroscopic morphology and precisely control microstructure. Polymer scaffolds are 1 of the commonly used 3D bioprinting materials for defect repair and have recently been a research focus. Our article explored the bone-formation accelerating effect of 3D-printed porous scaffold Poly(glycerol sebacate) [PGS] in the critical bone defect of an enhancing rabbit mandibular model. Also, we overview and summarize the classification of 3D bioprinting materials and prospects for their various application scenarios in craniofacial reconstruction surgery. Materials and methods: A PGS elastomer scaffold was prepared by polymerizing equimolar amounts of sebacic acid and glycerol using a biological 3D printer. Six male New Zealand white rabbits were prepared (3 for the control group and 3 for the PGS group), each weighing 3 kg. Osteotomy was performed at the anterior edge of the ascending ramus of the mandible with a bone saw to open the 8 mm defect. Defects of the control group were empty, and defects of the PGS group were put into 8 mm-wide PGS elastomer scaffolds. The rabbits were euthanized 6 weeks after the operation, and the postoperative mandibles were collected. Information (presence or absence of pus from infection, nonunion, degree of macroscopic bone healing) was recorded, and the skeletal tissue was fixed in a paraformaldehyde solution. Results: The mandible on the enhanced side was significantly longer than that on the opposite side, and the contralateral incisor was hyperplasia. The mandibles of rabbits in each group healed well, and there was no obvious local infection and purulence. The gross specimen appearance showed that both ends of the defect were connected. When comparing the reconstructed mandibles of the two groups, it is apparent that the width and thickness of the new bone in the PGS group were significantly better than that in the control group. Conclusions: This article verifies the effect of 3D polypore PGS scaffolds in animal craniomaxillofacial bone defects and introduces various application scenarios of 3D printing materials in craniomaxillofacial reconstruction surgery. There are quite good application prospects for 3D bioprinting in animal experiments and even clinical treatment of craniofacial defects.

The comprehensive on-demand 3D bio-printing for composite reconstruction of mandibular defects

[Application of Three-Dimensional Printing Technique in Repair and Reconstruction of Maxillofacial Bone Defect].

Application of CAD/CAM Techniques in Mandible Large-Scale Defect and Reconstruction with Vascularized Fibular Bone Graft

Systematic review on the application of 3D-bioprinting technology in orthoregeneration: current achievements and open challenges

Computer Aided Design and 3D Printing in Individual Reconstruction of Mandibular Defect

Direct Three-Dimensional Printing of a Highly Customized Freestanding Hyperelastic Bioscaffold for Complex Craniomaxillofacial Reconstruction

Research progress of 3D bio-printing technology in treatment of oral and maxillofacial bone defects

3D-Printed PEEK Implant for Mandibular Defects Repair - a New Method.

Regeneration of Critical‐Sized Mandibular Defects Using 3D‐Printed Composite Scaffolds: A Quantitative Evaluation of New Bone Formation in in vivo Studies

Preliminary Application Research of 3D Bioprinting in Craniofacial Reconstruction

Bone Tissue Engineering (BTE) of the Craniofacial Skeleton, Part II: Translational Potential of 3D-Printed Scaffolds for Defect Repair

Three-dimensionally printed polyetherketoneketone scaffolds with mesenchymal stem cells for the reconstruction of critical-sized mandibular defects

Advanced biomaterials for repairing and reconstruction of mandibular defects

Research progress of 3D printed poly (ether ether ketone) in the reconstruction of craniomaxillofacial bone defects

INDIVIDUALIZED SURGICAL GUIDANCE FOR MANDIBULAR RECONSTRUCTION USING 3D FEA/PRINTING TECHNOLOGIES

3D Bioprinting of a Bioactive Composite Scaffold for Cell Delivery in Periodontal Tissue Regeneration

The Challenge of 3D Bioprinting of Composite Natural Polymers PLA/Bioglass: Trends and Benefits in Cleft Palate Surgery

Advances in Three-Dimensional Printing for Craniomaxillofacial Trauma Reconstruction: A Systematic Review

In situ repair of bone and cartilage defects using 3D scanning and 3D printing

Bone Tissue Engineering through 3D Bioprinting of Bioceramic Scaffolds: A Review and Update

3D Printed Composite Structures for Bone Repair and Drug Delivery Application