Abstract:Background and objectives: Minimally-invasive total knee arthroplasty (MIS-TKA) has demonstrated very good short-term success, but its mid- to long-term results remain inconclusive. The success may be related to the tradeoff between a small incision and accurate positioning of the implant components. Patient-specific instrumentation (PSI) aims to improve the accuracy in restoring the knee axis and the clinical outcomes for MIS-TKA, but the results are yet to be confirmed by accurate assessment during functional activities. The purpose of the current study was to measure and compare the in vivo three-dimensional (3D) rigid-body and surface kinematics of MIS-TKA implanted with and without PSI during isolated knee active flexion/extension and sit-to-stand using state-of-the-art 3D model-based fluoroscopy technology. Methods: Ten patients treated for advanced medial knee osteoarthritis by MIS-TKA without PSI (non-PSI group) and nine with PSI (PSI group) participated in the current study. Each subject performed non-weight-bearing knee flexion/extension and sit-to-stand tasks while the motion of the prosthetic knee was under bi-plane fluoroscopy surveillance. The computer models of each of the knee prosthesis components were registered to the measured fluoroscopy images for each time frame via a novel validated 3D fluoroscopy method. Non-parametric 1-tailed Mann-Whitney tests were performed to detect the differences in the joint and surface kinematic variables every 10° of knee flexion between the non-PSI and PSI groups. The 1-tailed significance level was at α = 0.05. Results: The PSI group showed clear, coupled flexion/internal rotation during activities, while the non-PSI group remained roughly at an externally rotated position with slight internal rotations. The coupled rotation in the PSI group was accompanied by an anterior displacement of the medial contact and a posterior displacement of the lateral contact, which was different from the screw-home mechanism. Neither of the two groups showed the normal roll-back phenomenon, i.e., posterior translation of the femur relative to the tibia during knee flexion. Conclusions: With the state-of-the-art 3D fluoroscopy method, differences in both the rigid-body and surface kinematics of the prosthetic knees between MIS-TKA with and without PSI were identified. Patients with PSI demonstrated significant positive effects on the reconstructed rigid-body kinematics of the knee, showing clearer coupled flexion/internal rotations - an important kinematic characteristic in healthy knees - than those without PSI during activities with or without weight-bearing. However, none of them showed normal contact patterns. The current findings will be helpful for surgical instrument design, as well as for surgical decision-making in MIS total knee arthroplasty.

[Effect of femoral component rotational alignment in total knee arthroplasty by using 3D-printed patient-specific instruments: a prospective randomized control study].

Effect of 3D Printed Patient-Specific Cutting Guide on Patellar Height and Joint Line Position in Total Knee Arthroplasty

3D-printed patient-specific instrumentation decreases the variability of patellar height in total knee arthroplasty

Patient-Specific Instruments Based on Knee Joint Computed Tomography and Full-Length Lower Extremity Radiography in Total Knee Replacement.

[Effect of the Surgical Time and Coronalmechanical Alignment after Total Knee Arthroplasty Using Computer Navigation System, Traditionalor 3D Printing Patient-Specific Instruments].

Patient-specific instrumentation improves functional kinematics of minimally-invasive total knee replacements as revealed by computerized 3D fluoroscopy

The effects of femoral component design on the patello-femoral joint in a PS total knee arthroplasty

Efficiency assessment of intelligent patient-specific instrumentation in total knee arthroplasty: a prospective randomized controlled trial

The Posterolateral Corner-Locked Technique is Applicable in a Chinese Population Regarding the Tibial Component Rotation Alignment in Total Knee Arthroplasty.

Robotic-assisted total knee arthroplasty is more advantageous for knees with severe deformity: a randomized controlled trial study design.

Patient-Specific or Conventional Instrumentations: A Meta-analysis of Randomized Controlled Trials

Robot‐assisted total knee arthroplasty system provides more precise control of the femoral rotation angle: A retrospective study

Improved Component Placement Accuracy with Robotic-Arm Assisted Total Knee Arthroplasty

The Effects of Surgical Technique in Total Knee Arthroplasty for Varus Osteoarthritic Knee on the Rotational Alignment of Femoral Component: Gap Balancing Technique versus Measured Resection Technique

Higher satisfaction and function scores in restricted kinematic alignment versus mechanical alignment with medial pivot design total knee arthroplasty: A prospective randomised controlled trial

Preoperative evaluation of femoral and tibial sagittal alignment in robotic-assisted and conventional total knee arthroplasty and consequences for practice

[Comparison of Alignment and Position of Prosthesis Between Portable Accelerometer-Based Navigation Device and Conventional Instrumentation in Total Knee Arthroplasty with Valgus Deformity].

Patient‐specific instrumentation improved clinical outcome and implant survival but is not superior compared to conventional total knee arthroplasty: Ten years follow‐up of a multicenter double‐blind randomized controlled trial

Artificially Intelligent three-dimensionally (3D)-Printed Patient-Specific Instrument Improves total hip arthroplasty Accuracy

Quantitative Analysis of Rotational Alignment after Total Knee Arthroplasty in Osteoarthritis

Higher satisfaction after total knee arthroplasty using restricted inverse kinematic alignment compared to adjusted mechanical alignment