Abstract:Abstract In deep underground mining, achieving stable support for roadways along with long service life is critical and the complex geological environment at such depths frequently presents a major challenge. Owing to the coupling action of multiple factors such as deep high stress, adjacent faults, cross-layer design, weak lithology, broken surrounding rock, variable cross-sections, wide sections up to 9.9 m, and clusters of nearby chambers, there was severe deformation and breakdown in the No. 10 intersection of the roadway of large-scale variable cross-section at the − 760 m level in the Nanfeng working area of the Wuyang Coal Mine. As there are insufficient examples in engineering methods pertaining to the geological environment described above, the numerical calculation model was oversimplified and support theory underdeveloped; therefore, it is imperative to develop an effective support system for the stability and sustenance of deep roadways. In this study, a quantitative analysis of the geological environment of the roadway through field observations, borehole peeking, and ground stress testing is carried out to establish the FLAC 3D variable cross-section crossing roadway model. This model is combined with the strain softening constitutive (surrounding rock) and Mohr-Coulomb constitutive (other deep rock formations) models to construct a compression arch mechanical model for deep soft rock, based on the quadratic parabolic Mohr criterion. An integrated control technology of bolting and grouting that is mainly composed of a high-strength hollow grouting cable bolt equipped with modified cement grouting materials and a high-elongation cable bolt is developed by analyzing the strengthening properties of the surrounding rock before and after bolting, based on the Heok-Brown criterion. As a result of on-site practice, the following conclusions are drawn: (1) The plastic zone of the roof of the cross roadway is approximately 6 m deep in this environment, the tectonic stress is nearly 30 MPa, and the surrounding rock is severely fractured. (2) The deformation of the roadway progressively increases from small to large cross-sections, almost doubling at the largest cross-section. The plastic zone is concentrated at the top plate and shoulder and decreases progressively from the two sides to the bottom corner. The range of stress concentration at the sides of the intersection roadway close to the passageway is wider and higher. (3) The 7 m-thick reinforced compression arch constructed under the strengthening support scheme has a bearing capacity enhanced by 1.8 to 2.3 times and increase in thickness of the bearing structure by 1.76 times as compared to the original scheme. (4) The increase in the mechanical parameters c and φ of the surrounding rock after anchoring causes a significant increase in σ c and σ t ; the pulling force of the cable bolt beneath the new grouting material is more than twice that of ordinary cement grout, and according to the test, the supporting stress field shows that the 7.24 m surrounding rock is compacted and strengthened in addition to providing a strong foundation for the bolt (cable). On-site monitoring shows that the 60-day convergence is less than 30 mm, indicating that the stability control of the roadway is successful.

Similar simulation device for unloading effect of deep roadway excavation and its application

A Combined Method to Predict the Long-Term Settlements of Roads on Soft Soil under Cyclic Traffic Loadings

Undrained Behaviour of Intact Soft Clay under Cyclic Paths That Match Vehicle Loading Conditions

Experimental research on long-term dynamic characteristics of unsaturated road base and subbase mixtures

Behavior of Underground Structures under Large Area Loading

Influence Of Excavation Unloading On Vertical Bearing Behavior Of Existing Pile Groups

Method of Stress-Deformation Compatibility Analysis Considering Variable Mass for Roadbed Settlement

Influence of Deviatoric Stress on the Deformation and Damage Evolution of Surrounding Rock under Unloading Conditions

Model test on failure mechanisms of deep high-stress soft rock roadways based on excavation compensation method

Experimental Investigation on Engineering Disaster Simulation of Deep Buried Cavern Under Impact Load

Study on the failure mechanism of deep roadways considering gradient stress and the control technology of CFST supports

Experimental Study of Mechanical Behavior of Interlayer Staggered Zone under Cyclic Loading and Unloading Condition

Excavation unloading response of cylindrical rock-like specimen with axial joints: laboratory experiment and numerical simulation

True 3D geomechanical model test for research on rheological deformation and failure characteristics of deep soft rock roadways

Study on the Failure Mechanism for Coal Roadway Stability in Jointed Rock Mass Due to the Excavation Unloading Effect

Design and deformation pattern simulation of deep excavation support structures

Experimental research on deformation failure process of roadway tunnel in fractured rock mass induced by mining excavation

Failure Analysis of Intersections of Large-Scale Variable Cross-Section Roadways in Deep Soft Rock and Study of Integrated Control Technology of Bolting and Grouting

Experimental Study on Surrounding Rock Deformation and Acoustic Emission Characteristics of Rectangular Roadway under Different Loads

An Automated Large-Scale Apparatus for 3-D Cyclic Testing of Soil-Structure Interfaces

An innovative test to study cracking behavior of fractured rock-like material under stepped excavation unloading