Abstract:Zn-Li-based alloys have drawn great attention as promising candidates for load-bearing sites, such as intramedullary nails and bone plates. They possess high monotonic strength (over 500MPa) and better pitting resistance with lithium-rich layers acting as barriers for corrosion attack under (quasi-)static conditions. However, their response to dynamic loadings such as fatigue is still unknown. Herein, the corrosion fatigue behavior of a series of Zn-Li binary alloys with different lithium addition amounts was tested in simulated body fluid. Tensile and fatigue strength of the materials were proportional to lithium content while corrosion fatigue strength was not. Extremely long cracks that extended parallel to the loading direction were found in Zn-1.0wt.%Li alloys. These cracks propagated by selective dissolution of the lithium-rich phase in the eutectoid regions and drastically reduced the corrosion fatigue strength of Zn-1.0wt.%Li alloy owing to exacerbated crack propagation. To sum up, Zn-Li binary alloys showed fatigue strength comparable to pure iron and pure titanium, which confirmed their loading capacity under dynamic conditions. STATEMENT OF SIGNIFICANCE: Zn-Li-based alloys are qualified as biodegradable metals and are dedicated to load-bearing applications. Current research has shown that lithium can suppress pitting corrosion by the formation of lithium-rich layers on the alloy surface during (quasi-)static conditions. However, how these materials respond to dynamic loading is still unknown. The present study investigated the influence of lithium amount (0.1∼1.0wt.%) on the corrosion fatigue behavior of binary Zn-Li alloys. The results showed that lithium effectively improved the mechanical strength but can harm corrosion fatigue strength at high content due to selective dissolution of lithium-rich phase. This demonstrated that the amount of lithium should be controlled for optimal properties. Zn-0.8wt.%Li alloy demonstrated a good combination of tensile and corrosion fatigue strength, which can be further improved by proper alloying and thermomechanical treatment.

Suppression mechanism of initial pitting corrosion of pure Zn by Li alloying

Fatigue behavior of biodegradable Zn-Li binary alloys in air and simulated body fluid with pure Zn as control

Biodegradable Zn–Mn–Li alloy with a promising balance of mechanical property and corrosion resistance

Investigating the Stress Corrosion Cracking of a Biodegradable Zn-0.8 Wt%li Alloy in Simulated Body Fluid

Effects of trace amounts of lithium on the microstructure, mechanical properties, corrosion behavior, antibacterial activity and biocompatibility of Zn–Cu alloy

Investigation on the microstructural evolution and corrosion behaviors of Zn-microalloyed Al-Cu-Li alloys

Microstructure, Mechanical Properties and Corrosion Behaviors of Al–Li–Cu–Mg–Ag–Zn Alloys

Effects of Li addition on the properties of biodegradable Zn–Fe–Li alloy: Microstructure, mechanical properties, corrosion behavior, and cytocompatibility

Investigation of the Microstructure, Mechanical Properties, in Vitro Degradation Behavior, and Biocompatibility of Newly Developed Zn‐0.6%Li Alloy

Precipitate microstructures, mechanical properties and corrosion resistance of Al-1.0 wt%Cu-2.5 wt%Li alloys with different micro-alloyed elements addition

Ultrafine‐grained Zn‐0.45Li alloy with enhanced mechanical property, degradation behavior and cytocompatibility prepared by hot extrusion and multi‐pass drawing

Controllable Biodegradation and Enhanced Osseointegration of ZrO2-nanofilm Coated Zn-Li Alloy: in Vitro and in Vivo Studies.

The effect of major constituents on microstructure and mechanical properties of cast Al-Li-Cu-Zr alloy

Study of Electroless-Deposited Zn on the Surface of Mg-Li Alloy

A novel biodegradable nanocrystalline Zn alloy with exceptional biocompatible and antibacterial properties

Effect of ZnAl‐LDH on corrosion resistance of Zn–55Al alloy in NaCl solution

Effect of exposure time on corrosion behavior of zinc-alloy in simulated body fluid solution: Electrochemical and surface investigation

Enhanced Biocompatibility and Osteogenic Property of Biodegradable Zn-0.5Li Alloy through Calcium–Phosphorus Coating

Study on Corrosion Resistance of N36 Zirconium Alloy in LiOH Aqueous Solution

The Effect of 0.4 Wt.% Mn Addition on the Localized Corrosion Behaviour of Zinc in a Long-Term Experiment

In Situ Growth of High-Performance ZnAl-Layered Double Hydroxides/Al2O3 Composite Coatings on Aluminum Alloy