Abstract:Biodegradable Zn alloys show great potential for vascular stents due to their moderate degradation rates and acceptable biocompatibility. However, the poor mechanical properties limit their applications. In this study, low alloyed Zn-2Cu-xLi (x = 0.004, 0.01, 0.07 wt %) alloys with favorable mechanical properties were developed. The microstructure consists of fine equiaxed η-Zn grains, micron, submicron-sized and coherent nano ε-CuZn4 phases. The introduced Li exists as a solute in the η-Zn matrix and ε-CuZn4 phase, and results in the increase of ε-CuZn4 volume fraction, the refinement of grains and more uniform distribution of grain sizes. As Li content increases, the strength of alloys is dramatically improved by grain boundary strengthening, precipitate strengthening of ε-CuZn4 and solid solution strengthening of Li. Zn-2Cu-0.07Li alloy has the optimal mechanical properties with a tensile yield strength of 321.8 MPa, ultimate tensile strength of 362.3 MPa and fracture elongation of 28.0 %, exceeding the benchmark of stents. It also has favorable mechanical property stability, weak tension compression yield asymmetry and strain rate sensitivity. It exhibits uniform degradation and a little improved degradation rate of 89.5 μm∙year-1, due to the improved electrochemical activity by increased ε-CuZn4 volume fraction, and generates Li2CO3 and LiOH. It shows favorable cytocompatibility without adverse influence on endothelial cell viability by trace Li+. The fabricated microtubes show favorable mechanical properties, and stents exhibit an average radial strength of 118 kPa. The present study indicates that Zn-2Cu-0.07Li alloy is a potential and promising candidate for vascular stent applications. STATEMENT OF SIGNIFICANCE: Zn alloys are promising candidates for biodegradable vascular stents. However, improving their mechanical properties is challenging. Combining the advantages of Cu and trace Li, Zn-2Cu-xLi (x < 0.1 wt %) alloys were developed for stents. As Li increases, the strength of alloys is dramatically improved by refined grains, increased volume fraction of ε-CuZn4 and solid solution of Li. Zn-2Cu-0.07Li alloy exhibits a TYS exceeding 320 MPa, UTS exceeding 360 MPa and fracture EL of nearly 30 %. It shows favorable mechanical stability, degradation behaviors and cytocompatibility. The alloy was fabricated into microtubes and stents for mechanical property tests to verify application feasibility for the first time. This indicates that Zn-2Cu-0.07Li alloy has great potential for vascular stent applications.

Ultrafine‐grained Zn‐0.45Li alloy with enhanced mechanical property, degradation behavior and cytocompatibility prepared by hot extrusion and multi‐pass drawing

Investigation of the Microstructure, Mechanical Properties, in Vitro Degradation Behavior, and Biocompatibility of Newly Developed Zn‐0.6%Li Alloy

Effects of Li addition on the properties of biodegradable Zn–Fe–Li alloy: Microstructure, mechanical properties, corrosion behavior, and cytocompatibility

Microstructure Evolution, Mechanical Properties and Corrosion Behavior of Biodegradable Zn-2Cu-0.8Li Alloy During Room Temperature Drawing

300 MPa grade highly ductile biodegradable Zn-2Cu-(0.2-0.8)Li alloys with novel ternary phases

Enhanced mechanical properties and microstructural stability of ultrafine-grained biodegradable Zn-Li-Mn-Mg-Cu alloys produced by rapid solidification and high-pressure torsion

Strengthening Mechanism of Rotary-Forged Deformable Biodegradable Zn-0.45Li Alloys

Novel Zn-2Cu-0.2Mn-xLi (x = 0, 0.1 and 0.38) Alloys Developed for Potential Biodegradable Implant Applications

Hierarchical Structured Zn-Cu-Li Alloy with High Strength and Ductility and Its Deformation Mechanisms

Insight into Role and Mechanism of Li on the Key Aspects of Biodegradable ZnLi Alloys: Microstructure Evolution, Mechanical Properties, Corrosion Behavior and Cytotoxicity

Investigation on Microstructures, Mechanical Properties and in Vitro Corrosion Behavior of Novel Biodegradable Zn-2Cu-0.01Ti-xLi Alloys

Microstructure, mechanical properties and creep behaviour of extruded Zn-xLi (x= 0.1, 0.3 and 0.4) alloys for biodegradable vascular stent applications

Microstructures, Mechanical Properties and in Vitro Corrosion Behavior of Biodegradable Zn Alloys Microalloyed with Al, Mn, Cu, Ag and Li Elements

Optimization of mechanical properties and corrosion resistance of Zn-0.4Mn-0.8Li alloy using the hot rolling process

Development of high strength and ductile Zn-Al-Li alloys for potential use in bioresorbable medical devices

An in vitro and in vivo study of biodegradable Zn–Cu–Li alloy with high strength and ductility fabricated by hot extrusion combined with room-temperature ECAP

Microstructure, Mechanical Properties and Creep Behaviour of Extruded Zn-xLi (x = 0.1, 0.3 and 0.4) Alloys for Biodegradable Vascular Stent Applications

Developing Zn-2Cu-xLi (x < 0.1 wt %) alloys with suitable mechanical properties, degradation behaviors and cytocompatibility for vascular stents

Enhanced Mechanical Performance and Tailored Degradation Characteristics of Rolled Zn-0.8Li-0.4Mn Alloy

An in Vitro and in Vivo Study of Biodegradable Zn-Cu-Li - Cu - Li Alloy with High Strength and Ductility Fabricated by Hot Extrusion Combined with Room-Temperature ECAP