Abstract:This study focuses on alternatives to the sustainable management of plastic wastes through the development of a pyrolyser model, adapted to the recycling of plastics into fuel. It is a batch reactor, fixed bed, designed and built for the extraction of pyrolysis oil that can be recycled into petrol or diesel. The pyrolyser consists of a reactor with a volume of 0.0424 m3 and a copper spiral condenser with 2.31 m length. The plastics used for this study were Low Density PolyEthylene (LDPE), polypropylene (PP), polystyrene (PS) and polyethylene terephthalate (PET). They were collected from surrounding companies, washed, sampled, cut and sieved. Two different sizes of pyrolysis material: 1-3 cm (G1) and 3-7 cm (G2) were obtained and tested. The pyrolysis reactor and the plastics entering at an ambient temperature of 25 °C were heated. Plastics were then melted at 110 °C and vaporised at 450 °C. The hot vapour produced circulated through a copper coil and condensed. The resulting liquid was called pyrolysis oil. The results of this study show that the pyrolysis of LDPE, PP and PS yields two liquids: the heavy and majority fraction which arelike the conventional diesel and the light fraction which is like gasoline. Yields of 6-12.4% for the light fraction and 43.2-63.8% corresponding to the heavy fraction are observed. PE has the highest yield, 63.8% for the heavy fraction and 12.4% for the light fraction. The study further underscores that the size of the pyrolysis material influences the yields, i.e. an increase of 12.5, 9.1 and 7 % for LDPE, PS and PP respectively when the size of the pyrolysis material is increased from G2 to G1. In contrast, the results of PET have shown a liquid that solidifies 46 s later. It was also noticed that 2061.34 kJ of energy was required to pyrolyse 1 kg of plastic and produce 0.762 l of fuel. The simple physico-chemical characterisation of the majority fraction shows a great similarity with diesel fuel, as the distillation went beyond 200 °C. Therefore, we can say that the diesel fraction is similar to diesel fuel. We equally observed a high cetane number (52.1-55.1) and a high calorific value (42.9-55.5 MJ/kg). Consequently, there are some points of non-conformity with the European 590 standard and Cameroonian specifications for diesel fuel. These include a low density (767.8-815.1 kg/m3) and a low viscosity at 40 °C (1.108-1.346 mm2/S). A thorough physico-chemical analysis will complete this study before any recommendation for appropriate use.

Modelling and Validating the Nonthermal Plasma Parameters for Producing Liquid Hydrocarbon from Solid Polyolefin Wastes

Optimal Conversion of Food Packaging Waste to Liquid Fuel via Nonthermal Plasma Treatment: A Model-Centric Approach

CONVERSION OF WASTE POLYPROPILENE (PP) USING THE ZEOLITE Ni/ZSM-5 TO LIQUID FUEL

Optimisation of Process Parameters to Maximise the Oil Yield from Pyrolysis of Mixed Waste Plastics

An Investigation of a Hybrid Plasma Gasification System for Various Waste Plastics Thermochemical Degradation in the Fuel Extraction Process

Rapid Identification of Optimized Process Parameters Via RSM for the Production of Valuable Aromatic Hydrocarbons Using Multiphase Catalytic Pyrolysis of Mixed Waste Plastics

Direct Conversion of Poor‐quality Residual Oil to Light Gases in Electricity‐driven Thermal Plasma Reactor

Opportunities for converting waste plastics into petrochemicals: Process design, multi-objective optimization, and omnidirectional techno-economic-society-environment assessment

Design of a pyrolyser model for the conversion of thermoplastics into fuels

Response Surface Methodology Analysis of Pyrolysis Reaction Rate Constants for Predicting Efficient Conversion of Bulk Plastic Waste into Oil and Gaseous Fuels

Optimisation of a catalytic hydrothermal liquefaction process using central composite design for yield improvement of bio-oil

Modeling and simulation of microwave assisted catalytic pyrolysis system of waste plastics polymer for fuel production

Continuous flow pyrolysis of virgin and waste polyolefins: a comparative study, process optimization and product characterization

Integrated Waste-to-Energy Process Optimization for Municipal Solid Waste

Simulation and Modelling of Hydrogen Production from Waste Plastics: Technoeconomic Analysis

Liquid fuel oil produced from plastic based medical wastes by thermal cracking

Production efficiency and safety assessment of the solid waste-derived liquid hydrocarbons

An Aspen plus process simulation model for exploring the feasibility and profitability of pyrolysis process for plastic waste management

On the operating parameters for hydrogen-rich syngas production in a plasma co-gasification process of municipal solid wastes and polypropylene using a constrained model in Aspen plus

Production of hydrogen-rich fuel gas from waste plastics using continuous plasma pyrolysis reactor

THERMAL CATALYTIC PYROLYSIS PROCESS STUDIES FOR POST CONSUMER POLYETHYLENE WASTE CONVERSION