Abstract:Objective: To investigate the influence of light and heavy bite force on the mandibular movement trajectories, and the influence of bite force on virtual occlusal pre-adjustment of digital full crown. Methods: From October 2021 to March 2022, 10 postgraduate volunteers (3 males and 7 females, aged 22-26 years) were recruited from Peking University School and Hospital of Stomatology. Maxillary and mandibular digital models of the participants were obtained by intraoral scanning. Jaw relations were digitally transferred under heavy bite force and mandibular movement trajectories under light and heavy bite force were recorded by jaw motion analyser. Three mandibular markers were chosen, namely the mesial proximal contact point of the central incisor (incisal point) and the mesial buccal cusp tips of the bilateral first molars. The three-dimensional displacements of the markers under two kinds of bite force in the intercuspal position (ICP), the sagittal projection of the three-dimensional displacements in the protrusive edge-to-edge position, and the coronal projection of the three-dimensional displacements in the lateral edge-to-edge position of upper and lower posterior teeth were measured. Single-sample t-test was used to compare the three-dimensional displacements and the corresponding sagittal projection and coronal projection with 0, respectively. The left maxillary central incisor and left mandibular first molar were virtually prepared by the reverse engineering software. Then dental design software was used to design digital full crown using the copy method. The mandibular movement trajectories under light and heavy bite force were separately used to guide virtual occlusal pre-adjustment. The three-dimensional deviations (mean deviations and root mean square) between the lingual surface of the left maxillary central incisor or the occlusal surface of the left mandibular first molar and that of the natural tooth before preparation were calculated (light bite force group and heavy bite force group), and the differences between the two groups were compared by the paired t-test. Results: Under the two kinds of bite force, the three-dimensional displacements of the markers in the ICP were (0.217±0.135), (0.210±0.133) and (0.237±0.101) mm, respectively; the sagittal projection of the three-dimensional displacements of the markers in the protrusive edge-to-edge position were (0.204±0.133), (0.288±0.148) and (0.292±0.136) mm, respectively; the coronal projection of the three-dimensional displacements of the mesial buccal cusp tips of the bilateral first molars in the lateral edge-to-edge position were (0.254±0.140) and (0.295±0.190) mm, respectively. The differences between the above displacements and 0 were statistically significant (P<0.05). The results of occlusal pre-adjustment showed that the mean deviations of the lingual surface of the left maxillary central incisor in the light and heavy bite force groups were (0.215±0.036) and (0.195±0.041) mm (t=3.95, P=0.004), respectively. The mean deviations of the occlusal surface of the left mandibular first molar were (0.144±0.084) and (0.100±0.096) mm (t=0.84, P=0.036), respectively. Conclusions: Both the light and heavy bite force have an influence on the mandibular movement trajectories. Virtual occlusal pre-adjustment of prostheses with mandibular movement trajectories under heavy bite force can obtain morphology of lingual or occlusal surfaces closer to the natural teeth before preparation.

Digital testing system for tooth touch function

Automatic method for quantitative detection of vibration perception threshold

Digital measurement method for comparing the absolute marginal discrepancy of three-unit ceramic fixed dental prostheses fabricated using conventional and digital technologies

A User-Friendly Packaging Solution for Silicon-Based Pressure Die to Develop Prosthetic Tactile Sensing

A Mechatronic Platform for Studies of Tactile Sensory System on Prosthesis Hand

A Mechatronic Platform for Calibration and Performance Test of Extrinsic Tactile Sensor on Prosthesis Hand.

Penalty-based Haptic Rendering Technique on Medicinal Healthy Dental Detection

Development of new measuring system and method for intraoral pressure

[Development and Preliminary Application of Orthodontic Friction Dynamic Testing Apparatus].

Digital Interactive Design and Robot-Assisted Preparation Experiment of Tooth Veneer Preparation: An in Vitro Proof-of-Concept

Probe for detecting and diagnosing palate roots of maxillary molar teeth

[Measurement of Tactile Threshold of Natural Teeth and Its Clinical Significance].

Dental Training System for Probing Operation with Visual and Force Display

Experimental and numerical estimations into the force distribution on an occlusal surface utilizing a flexible force sensor array

Tooth movement tendency of space closure by sliding mechanics in customized lingual appliance: A 3-dimensional finite element analysis

Method and apparatus for tooth body automatic preparation by digital controlled laser light and tooth retainer

[Study on mandibular movement trajectory and virtual occlusal pre-adjustment under light and heavy bite force].

A Development of 3 - D Image Survey System for Tooth Wear Measurement

A Digital Technique for Occlusal Design of a Posterior Full Crown Based on Physiological Tooth Displacement and Occlusion of Adjacent Teeth.

Finite element analysis of tooth movement under different retraction force and intrusive force in double-archwire lingual orthodontics system

Evaluation of biomechanics using different traction devices in distalization of maxillary molar with clear aligners: a finite element study