Abstract:Organic-inorganic metal halide perovskite solar cells (PSCs) have been widely studied due to their excellent photoelectric conversion performance, but the inherent chemical instability of CH(NH 2 ) 2 PbI 3 (FAPbI 3 ) has hindered its long-term development. In particular, the surface interface of the membrane has prominent humidity sensitivity due to lower activation energy, the defect of the surface interface has a strong correlation with the film stability, and the treatment result of the defect is one of the key factors to improve the long-term stability. FAPbI 3 suffers phase transition from black perovskite phase to yellow non-perovskite phase at room temperature, and the moisture will accelerate this phase transition. Interface engineering is one of the common methods to improve the stability of perovskite solar cells. In addition to interface engineering, there is also a strategy of stacking a two-dimensional (2D) perovskite layer on the surface for interface passivation. However, the preparation methods of 2D perovskite layer are most limited. In this paper, through the preparation process of the whole solution method and post-treatment mode of annealing were adopted, the hybrid perovskite solar cells of vitamin perovskite were successfully prepared. FAPbI 3 perovskite surface was uniformly spin-coated with butylamine iodide (BAI) solution, and the formation of 2D perovskite was driven on the surface of FAPbI 3 perovskite. Due to the passivation of 2D perovskite layer on the defects at the surface interface, the carrier non-radiative recombination is reduced, so that the carrier lifetime is greatly improved. Due to the hydrophobicity of long chain molecules in 2D perovskite, the long-term stability of the device has been significantly improved. Consequently, the unencapsulated device containing 2D perovskite layer remained above 80% after working nearly 1000 hours of relative humidity (RH) of 60% in ambient air at room temperature. The 2D perovskite layer can significantly improve the long-term stability of the film without affecting the charge carrier transport performance. This method to improve the stability of the device by constructing 2D perovskite layer is in line with the requirements and development trend of high-quality perovskite solar cells, and is a strategy with great development potential.

Method for improving stability of perovskite film through sulphuring treatment

Enhanced Moisture Stability of Metal Halide Perovskite Solar Cells Based on Sulfur-Oleylamine Surface Modification

Excellent Stability of Perovskite Solar Cells by Passivation Engineering

Enhanced Stability and Efficiency of Perovskite Solar Cells Via Bifunctional Group Passivation with Thiosalicylic Acid

Enhancing the Humidity Stability of Perovskite Films through Interfacial Modification with Differentiated Hydrophilic Organics

Improved photostability of metal halide perovskites by microstructure modulation for photovoltaic application

Aqueous solvent-regulated crystallization and interfacial modification in perovskite solar cells with enhanced stability and performance

Stability Improvement of Tin‐Based Halide Perovskite by Precursor‐Solution Regulation with Dual‐Functional Reagents

Improving the stability and performance of perovskite solar cells via off-the-shelf post-device ligand treatment

Hydrochloric acid-assisted method for preparing organic and inorganic hybrid perovskite material

Stabilizing halide perovskite surfaces for solar cell operation with wide-bandgap lead oxysalts

Method for preparing thermal-stability perovskite CsPbI3 by dual-amino organic matter

Forming enlarged grain and fixed boundary via a two-step surface modification to achieve stable inverted perovskite solar cells

Post-treatment by an ionic tetrabutylammonium hexafluorophosphate for improved efficiency and stability of perovskite solar cells

Reactive Inhibition Strategy for Triple‐cation Mixed‐halide Perovskite Ink with Prolonged Shelf‐life

Preparation of 2D Perovskite Layer by Solution Method to Improve the Stability of FAPbI 3 Perovskite Solar Cells

Stabilizing the MAPbI 3 Perovksite Via the In-Situ Formed Lead Sulfide Layer for Efficient and Robust Solar Cells

Improving Crystallization and Stability of Perovskite Solar Cells Using a Low-Temperature Treated A-Site Cation Solution in the Sequential Deposition

Enhancing Organic‐Inorganic Perovskite Thin Film Crystallization via Vapor‐Solid Reaction by Modifying PbI2 Precursors films with Pyridinium Trifluoromethanesulfonate

Chemical encapsulation of perovskite film by tetra-thiol copper(II) porphyrin for stable and clean photovoltaics

Reducing surficial and interfacial defects by thiocyanate ionic liquid additive and ammonium formate passivator for efficient and stable perovskite solar cells