Abstract:Upward- (UFS) and downward (DFS) flame spread along a vertical installed electrical wire has been examined experimentally to gain better understandings of the heat transfer mechanism and burning behavior over electrical wires. UFS is considered as a much more hazardous fire scenario than DFS, however, UFS over electrical wires was very limited addressed. Fundamentally, the controlling heat transfer boundary over the preheating zone, hence the flame spread behaviors are quite different between DFS and UFS. This problem is more complicated for an electrical wire, for which the metal conduction is involved additionally, playing an important role in the heat transfer process. Thirteen types of polyethylene-insulated electrical wires with Cu- and NiCr-core were used to investigate the effect of metal core thermal conduction and wire configuration for both UFS and DFS. During the flame spread process, the pyrolysis length of UFS was enlarged, while only portion of virgin material of DFS were burnt as the result of distinct dripping. By further concerning the curvature effect, the dependence of the flame length on heat release rate per unit width (i.e. perimeter for cylinder) can be well explained by non-dimensional analysis. It turns out that the growth of flame length will be restrained as radius decreases significantly, and can be categorized in to two regions, one is controlled by laminar molecular diffusion followed the other controlled by turbulent entrainment. The variation of flame spread rate (FSR) with wire configuration and metal core thermal conduction are well interpreted by a theoretical model, which describes the heat recirculation through flame-insulation-core comprehensively based on thermodynamics theories, and attempts to consider the effects of temperature gap between core and insulation at pyrolysis front, burning fraction and melting heat. The validity of this new model is well confirmed by measured FSR. An important finding is that a highly conductive core will trigger an acceleration of FSR over the wire, primarily because heat flux in gas phase is more sensitive to the change of core thermal conductivity than heat conduction through core. Even though the heat diffusion length increases at the same time, however, the heat flux in gas phase grows faster than the corresponding heat loss through core, thereby compensate the corresponding heat loss. This work could facilitate understanding of heat transfer mechanism and burning behavior not only on the electrical wires, but also on the composite material with high thermal-conductive media.

Fire Zone Diagram of Flame-retardant Cables: Ignition and Upward Flame Spread

Fire Behaviors of Flame-Retardant Cables Part I: Decomposition, Swelling and Spontaneous Ignition

Experimental study on fire spread behavior of single 110 kV cable under different layout conditions

Flame Spread Experiments on a Horizontal Preheated Cable Layer

Experimental Study on Flammability and Flame Spread Characteristics of Polyvinyl Chloride (PVC) Cable

Influence of Arc Size on the Ignition and Flame Propagation of Cable Fire

A Comparative Study on Fire Hazards of Cables Used in Nuclear Power Plants Based on Small- and Large-Scale Experiments

Trees in 110 kV XLPE cable insulation at high temperature

Flame-Retardant Wire Burning Behavior by Jet Flame Heating: Ignition, Charring, and Secondary Flame Spread

Preliminary Real-scale Experimental Studies on Cable Fires in Plenum

Analysis of Upward- and Downward Flame Spread over Vertical Installed Polyethylene-Insulated Electrical Wires

An Experimental Analysis of a Nuclear-Grade Cable Based on Fire Combustion Characteristics and Pyrolysis Behavior

Investigation of the flammability of different cables using pyrolysis combustion flow calorimeter

Flammability degradation behavior and ageing mechanism of flame-retardant cable sheath under different ageing conditions

Real Scale Tests On Cable Tray Fires To Simulate Actual End User'S Condition

Quantitative inner heat transfer for cable fire: a numerical study and effects of core diameter and insulation thickness

Analysis of Heat Transfer During Flame Spread over Energized-Wire under High Currents

Failure characteristic of class 1E electrical cable used in the nuclear power plant exposed to fire

An experimental facility for detailed burning mechanisms of flame-retardant cables based on an annular vertical heating chamber

On the pyrolysis characteristic parameters of four flame-retardant classes of PVC sheathless cable insulation materials

Investigating the Burning Characteristics of Electric Cables Used in the Nuclear Power Plant by Way of 3-D Transient Fds Code