Abstract:The microstructural evolution and mechanical properties of cast high-Li-content TiB2/Al-Li-Cu composite during heat treatment were systematic investigated by a combination of various techniques, including transmission electron microscopy (TEM) with HAADF-STEM mode, electron backscatter diffraction (EBSD), scanning electron microscopy (SEM) and differential scanning calorimetry (DSC). The coarse secondary phases, mixed with clusters of relatively larger TiB2 particles, distributed along grain boundaries were observed in as-cast state. And most of them dissolved into the α-Al matrix after a two-stage solution treatment. The grain size of the studied composite exhibited excelled thermal stability owing to effective pinning grain boundaries by the stable particles at the elevated temperature, resulting in no significant increase after solution treatment. The studied composite showed a strong age-hardening response with the peak-hardness was obtained in about 160 h at 175 °C. TEM results showed much fine δ′ precipitates were uniformly distributed within grains after quenching and it coarsened with the increasing age duration. Fine plate-like θ′ and T1 precipitates were observed in the under-aged (UA, aged for 8 h) condition. The rate of precipitation and growth in its diameter was much greater than its coarsening rate, resulted in the large aspect ratio and high number density of T1 and θ′ precipitates were visible in the peak-aged (PA) condition. Finally, a slight decline in hardness was observed in the over-aged (OA) condition due to the apparent coarsening of θ′ and T1 precipitates. This precipitation behavior was further verified by DSC. After appropriate heat treatment, a good comprehensive mechanical properties could be obtained in the composite.

Microstructure Characteristics for Quench Sensitivity of In-Situ TiB2/7050Al Composite

The quench sensitivity of SiCp/2024Al composites based on Jominy end quench test

Detailed investigation of quench sensitivity of 2050 Al-Cu-Li alloy by interrupted quenching method and novel end quenching method

Microstructure evolution during preparation of in-situ TiB reinforced titanium matrix composites

Precipitation Behavior of the High-Li-content In-Situ TiB2/Al-Li-Cu Composite

Quench sensitivity of SiCp/2024Al metal matrix composites

Microstructure and Damping Behavior of In-situ TiB2/A356 Aluminum Matrix Composites

Quench sensitivity and microstructure evolution of the 2060 Al-Cu-Li alloy with a low Mg content

Microstructure characterization and enhanced mechanical properties of quasi-continuous network structured Ti3AlC2-Al3Ti/2024Al composite

Microstructural evolution and mechanical properties of cast high-Li-content TiB 2 /Al-Li-Cu composite during heat treatment

An Investigation of Microstructural Evolution, Tensile Properties and Work-Hardening Behavior of Nanosized TiB2/Al-Cu-Mn Composites

Effects of Nanosized Particles on Microstructure and Mechanical Properties of an Aged In-Situ TiB2/Al-Cu-Li Composite

Microstructure characterization and mechanical properties of TiB 2/TiAl in situ composite by induction skull melting process

An Investigation of Microstructural Evolution, Tensile Properties and Work-Hardening Behavior of Nanosized TiB<sub>2</sub>/Al-Cu-Mn Composites

SEM and TEM characterization of the microstructure of post-compressed TiB2/2024Al composite.

Microstructure Characterization of Al Matrix Composite Reinforced with Ti–6Al–4V Meshes after Compression by Scanning Electron Microscope and Transmission Electron Microscope

Insight into the recrystallization behavior and precipitation reaction of in-situ nano TiB2/Al Cu Mg composite during heat treatment

Microstructure characterization of Al matrix composite reinforced with Ti-6Al-4V meshes after compression by scanning electron microscope and transmission electron microscope.

Quench Sensitivity of 6351 Aluminum Alloy

Quench Sensitivity of a 7A46 Aluminum Alloy

Insight into the recrystallization behavior and precipitation reaction of in-situ nano TiB2/AlCuMg composite during heat treatment