Abstract:A major problem of additively manufactured parts using laser powder bed fusion (LPBF) is the as-built high surface roughness. The poor surface finishing is detrimental to the mechanical and electrochemical properties of the parts. In this work, we present systematic investigations on surface roughness reduction of LPBF produced nickel-based superalloy Hastelloy X (HX) using electropolishing. The electrolyte used in this study is an environmentally safe deep eutectic solvent (DES) comprising a eutectic mixture of choline chloride and ethylene glycol in a 1:2 M ratio, respectively. Two different groups of LPBF HX parts separated for the purpose of electropolishing the external and internal surface were prepared. The results show that both the external and internal surface roughness can be effectively reduced using electropolishing in DES. For the parts with the external surface electropolished for 5 min, a surface roughness reduction down to 1.2 μm (Ra) with a bright and reflective surface appearance was achieved. This is a significant improvement in comparison to the high as-built surface roughness of 10.3 μm (Ra) with a dull and non-reflective surface appearance. For the internal surface electropolishing, the surface quality of a 3 mm diameter internal channel in an angled LPBF HX cylindrical tube was successfully enhanced. The DES electropolishing efficiency on LPBF HX was investigated using weight reduction as a function of the electropolishing time, and the microstructure of the electropolished LPBF HX was studied. A further improvement of the electrochemical properties for the electropolished surface was revealed by anodic polarization tests and electrochemical impedance tests. The electropolished surface was also revealed to be more hydrophobic than the as-built surface by water contact angle tests, which is beneficial to the corrosion resistance. The findings herein demonstrate the surface quality of the LPBF produced HX can be effectively improved using electropolishing, and also showed the feasibility of using DES as a promising alternative electrolyte to the conventional hazardous acid mixtures.

Effect of Electrolyte Solutions on the Electrochemical Dissolution Behavior of Additively Manufactured Hastelloy X Superalloy Via Laser Solid Forming

Anodic dissolution behavior of the complex microstructure of laser directed energy deposited Alloy 718 during electrolyte jet machining in NaCl-ethylene glycol electrolyte

Optimizing the surface quality of electrochemical machined Ni-based single crystal superalloy via manipulation of phase and dendrite dissolution

Microstructure and anodic electrochemical behavior of additive manufactured Hastelloy X alloy via directed energy deposition

Anodic Dissolution Behavior of DD6 Nickel-Based Single Crystal Superalloy for Electrochemical Machining Applications

Study on anodic dissolution behavior and surface evolution of laser-drilled Ni-based superalloys during electrochemical post-processing

The Anisotropic Electrochemical Machinability of Laser Cladding Deposited Ti6Al4V Alloy in NaCl Solution

Electrochemical Anisotropy of Hastelloy X Fabricated by Selective Laser Melting in a NaNO 3 Solution

Investigation of surface roughness post-processing of additively manufactured nickel-based superalloy Hastelloy X using electropolishing

Titanium Alloy Ti-6Al-4V Electrochemical Dissolution Behavior in NaNO3 and NaCl Solutions at Low Current Density

The Microstructures and Mechanical Properties of a Welded Ni-Based Hastelloy X Superalloy

Study on the Effect of Electrolytes on Processing Efficiency and Accuracy of Titanium Alloy Utilizing Laser and Shaped Tube Electrochemical Machining

Electrochemical Behavior of Laser Powder Bed Fusion (L-PBF) Ti–6Al–4V Alloy: Influence of Phase and Grain Boundaries on Surface Passive Film Formation

Recrystallization effect on surface passivation of Hastelloy X alloy fabricated by laser powder bed fusion

Electrochemical Machining of Micro-Pit Arrays on a GH4169 Alloy with a Roll-Print Mask Using a C6H5Na3O7-Containing NaNO3 Mixed Electrolyte

Electrolyte Jet Machining of Ti1023 Titanium Alloy Using NaCl Ethylene Glycol-Based Electrolyte

Synergistic effect of transpassive film and gamma double prime phase on the electrochemical dissolution behavior of Inconel 718 manufactured by laser directed energy deposition

Passivation Behavior of S136H Steel in Neutral Electrolytes Composed of NaClO3 and NaNO3 and Its Influence on Micro Electrochemical Machining Performance

Electrochemical surface modification of GH4742 nickel-based superalloy in C6H5Na3O7 solution

Surface morphology and electrochemical behaviour of Ti-48Al-2Cr-2Nb alloy in low-concentration salt solution

Anodic Dissolution Characteristics of GH4169 Alloy in NaNO3 Solutions by Roll-Print Mask Electrochemical Machining Using the Linear Cathode