Abstract:Bi2Te3-based compounds are currently the most commercially relevant thermoelectric materials near room temperature. They are prepared via hot pressing, hot deformation, spark plasma sintering, and other consolidation processes, which are typically performed at 400–500 °C. Such high-temperature processes are energy-intensive and generate unnecessary waste heat, making them undesirable for a large-scale production. In this study, a low-temperature liquid-phase-assisted sintering (or so-called cold-sintering) process was employed to fabricate p-type Bi0.5Sb1.5Te3 bulk materials at temperatures below 150 °C. At the optimal sintering temperature (130 °C), a ZT value as high as 0.56 at 450 K can be achieved, competitive to that of a commercial Bi0.5Sb1.5Te3 ingot (ZT 0.8–1.0). The addition of a small amount of transient liquid facilitates grain reorientation and expedites a mass transfer process under axial compaction and liquid evaporation conditions, thus resulting in nearly fully densified Bi0.5Sb1.5Te3 pellet samples (>97% theoretical density). Furthermore, the low-temperature sintering process results in the reduction of grain size and promotes twin boundaries, resulting in a low lattice thermal conductivity of 0.57 W m–1 K–1 at 380 K due to phonon scattering. The strategy reported in this work can be used not only as a substitute for high-temperature sintering of other thermoelectric materials but also to engineer phonon scattering for high-performance thermoelectrics.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.1c03540.Single parabolic band model and calculated transport properties; EBSD analysis for pellet sintered at 110 °C; BSE, EDS mapping, and TEM images of pellet sintered at 130 °C; average ZT values; and XPS results (PDF)This article has not yet been cited by other publications.

Cryogenic thermoelectric enhancements in SbCl 3 -doped porous Bi 0.85 Sb 0.15 alloys

Cryogenic Thermoelectric Enhancements in SbCl3-doped Porous Bi0.85Sb0.15 Alloys

Enhanced Figure of Merit in Bismuth-Antimony Fine-Grained Alloys at Cryogenic Temperatures

Mid-temperature Thermoelectric Performance of Zone-Melted Sb2(Te,Se)3 Alloys Near Phase Transition Boundary

Enhanced mechanical and thermoelectric properties enabled by hierarchical structure in medium-temperature Sb2Te3 based alloys

Enhanced Thermoelectric and Mechanical Performances in Sintered Bi 0.48 Sb 1.52 Te 3 –AgSbSe 2 Composite

Synergistically enhanced thermoelectric properties of Bi2S3 bulk materials via Cu interstitial doping and BiCl3 alloying

Enhanced Thermoelectric and Mechanical Performances in Sintered Bi0.48Sb1.52Te3-AgSbSe2 Composite.

Cold-Sintered Bi 2 Te 3 -Based Materials for Engineering Nanograined Thermoelectrics

Thermoelectric Performance of P-Type Zone-Melted Se-doped Bi 0.5 Sb 1.5 Te 3 Alloys

Enhanced Thermoelectric Properties Obtained by Compositional Optimization in P -Type Bi X Sb 2− X Te 3 Fabricated by Mechanical Alloying and Spark Plasma Sintering

Improved Thermoelectric Properties of BiSbTe-AgBiSe 2 Alloys by Suppressing Bipolar Excitation

Expand band gap and suppress bipolar excitation to optimize thermoelectric performance of Bi0.35Sb1.65Te3 sintered materials

Enhanced Thermoelectric Performance of Bi2s3 by Synergistical Action of Bromine Substitution and Copper Nanoparticles

High-Thermoelectric Performance of Nanostructured Bismuth Antimony Telluride Bulk Alloys

Thermoelectric and thermomechanical properties of the hot pressed polycrystalline Bi0.5Sb1.5Te3 alloys

Improved figure of merit (z) at low temperatures for superior thermoelectric cooling in Mg3(Bi,Sb)2

Porous bismuth antimony telluride alloys with excellent thermoelectric and mechanical properties

Enhancing thermoelectric properties of p-type (Bi,Sb)2Te3 via porous structures

High Thermoelectric Performance Bismuth Telluride Prepared by Cold Pressing and Annealing Facilitating Large Scale Application

Synergistically Optimized Thermoelectric and Mechanical Properties in p ‐Type BiSbTe by a Microdroplet Deposition Technique