Abstract:Ti2AlNb alloy is a new type of lightweight and heat-resistant structural material that has been an active research topic with multi-phases due to its improved mechanical properties. However, the phase response under severe plastic deformation (SPD) at high strain rates is unclear, which limits the understanding of its strengthening mechanism. Here, laser shock peening (LSP) was employed to investigate the microstructure response of alpha 2, O, and B2/beta phases in Ti2AlNb alloy. After LSP, the highest density dislocations were generated in the B2/beta phases, followed by the O phases, and the least dislocations were observed in the alpha 2 phases. In the B2/beta phases, only dislocation tangles (DTs) were observed. Dislocation lines (DLs) and DTs were mainly distributed in the O phases. As for the alpha 2 phases, DLs were generated while a small number of DTs were piled up at the grain boundaries. In addition, parallel dislocations (PDs) with a spacing of about 135 nm can be observed on the surface of the alpha 2 phases, and the dislocations interspersed between PDs were composed of screw dislocations with long segments. In addition to dislocation structures, stacking faults (SFs) were observed in both alpha 2 phases and O phases, and mechanical twins were formed in the O phases, which were generated to coordinate the SPD induced on the surface. These dislocation structures formed dislocation cells (DCs) and sub-grain boundaries which further developed into high-angle grain boundaries (HAGBs) together with mechanical twins, dividing the coarse grains and refining the microstructure. As the depth increased, the responses of the three kinds of phases decreased. The PDs in the alpha 2 phases have widened spacing and could not penetrate the grains. The mechanical twins were gradually reduced until no obvious twin structure could be observed. Finally, dislocations, grain size, microhardness, and residual stress presented a gradient distribution. The improved microhardness (maximum 470 HV) and compressive residual stress (maximum -600 MPa) which were consistent with the refined grains and highdensity dislocations gradually decreased to that of the base metal (BM).

Finite Element Simulation on Bending Properties of TA2/TA15 Gradient Material by Laser Direct Deposition

Microstructure and Mechanical Properties of Ti60-Ti2alnb Functionally Graded Materials Fabricated by Laser Directed Energy Deposition

Investigation on the Microstructure and Mechanical Behaviors of a Laser Formed Nb-Ti-Al Alloy

Insights into the gradient microstructure and mechanical properties of Ti-6.5Al–2Zr–Mo–V alloy manufactured by electron beam freeform fabrication

Microstructural and texture evolution investigation of laser melting deposited TA15 alloy at 500?C using in-situ EBSD tensile test

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Study on Microstructure and Properties of Additive-Manufactured TC4ELI+TC21 Titanium Alloy Gradient Composite Structures

Microstructure Evolution and Mechanical Behavior of Laser Melting Deposited TA15 Alloy at 500 °C under In-Situ Tension in SEM

Microstructure and mechanical properties of Ti60–Ti 2 AlNb functionally graded materials fabricated by laser directed energy deposition

Temperature gradient induced tough-brittle transition behavior of a high-strength Al-4.2Mg-0.4Sc-0.2Zr alloy fabricated by laser powder bed fusion additive manufacturing

In Situ Electron Backscatter Diffraction Study of Deformation Inhomogeneity under Uniaxial Tension of Laser Melting Deposited TA15 Alloy

Chemical, microstructure, and mechanical property of TiAl alloys produced by high-power direct laser deposition

Tensile and superelastic behaviors of Ti-35Nb-2Ta-3Zr with gradient structure

Gradient microstructure response in different phases of Ti<sub>2</sub>AlNb alloy with laser shock peening

Microstructure characterization of gradient composition between TC25G and TiAl alloys prepared by directed energy deposition technique

Study on High-Temperature Flow Behavior and Substructure and Texture Evolution of TA15 Titanium Alloy

Characterization of the deformation behavior and microstructure evolution in laser bending of TC4 titanium alloy heavy plate

Formation Mechanism of Dilute Region and Microstructure Evolution in Laser Solid Forming TA15/Ti2AlNb Dual Alloy

Suppression of texture and enhancement of high-temperature tensile property in heavily deformed gradient Ti 2 AlNb alloy

Laser Deposition of Ti6Al4V-316L Composition Gradient Structure: Challenge on Intermetallics