Abstract:Power conversion efficiency (PCE) of organic solar cells (OSCs) has reached the threshold for application. However, the high PCEs are mostly obtained from the small‐area OSCs processed by the halogenated solvent, such as chloroform (CF), because the high‐performance A‐DA'D‐A type small molecule acceptors (SMAs) need the CF processing for suitable solubility and rapid solvent evaporation to get appropriate aggregation morphology. Herein, we synthesized two new A‐DA'D‐A type SMAs of Y6‐Ph and L8‐Ph by introducing a phenyl end group in the branched alkyl inner side chains of the representative SMAs Y6 and L8‐BO respectively, for overcoming the excessive aggregation of SMAs in the long‐time film‐forming process in the nonhalogenated solvent processing. Firstly, we studied the effect of the processing solvent boiling point on the aggregation property and photovoltaic performance of the four SMAs of Y6, L8‐BO, Y6‐Ph and L8‐Ph, by using the most commonly used halogenated processing solvents: low‐boiling‐point CF (rapid film forming process) and high‐boiling‐point chlorobenzene (CB) (slow film forming process) for device fabrication of the OSCs with PM6 as polymer donor. It was found that the Y6‐ and L8‐BO‐based OSCs exhibit a dramatic drop in PCEs from CF‐ to CB‐processed devices owing to the large phase separation in the CB‐processed OSCs. On the contrary, the devices based on Y6‐Ph and L8‐Ph with the phenyl ending inner side chains show obviously increased PCEs for the OSCs processed by high‐boiling‐point CB. The L8‐Ph‐based devices processed by CB demonstrated an PCE of 18.83% with a high FF of 80.55%, which is even better than the L8‐BO‐based OSCs processed by CF. Furthermore, the L8‐Ph‐based OSCs processed by nonhalogenated solvent o‐xylene (o‐XY) also achieved a high PCE of 18.40% with an FF of 80.11%, which is the best‐performed OSC fabricated from the nonhalogenated solvents so far. In addition, the large‐area (1 cm2) OSCs based on PM6:L8‐Ph processed by o‐XY also demonstrated a higher PCE of 16.66%. The results indicate that introducing phenyl end group in the inner side chains is an effective strategy to improve photovoltaic performance of the A‐DA'D‐A SMAs for future application of the OSCs with nonhalogenated solvent processing. This article is protected by copyright. All rights reserved

Achieving 10% efficiency in non-fullerene all-small-molecule organic solar cells without extra treatments

High-efficiency organic solar cells based on a small-molecule donor and a low-bandgap polymer acceptor with strong absorption

Hydrogen Bond‐Induced Cathode Engineering Enables Binary All‐Small‐Molecule Organic Solar Cells with 15.88% Efficiency and Enhanced Thermostability

Asymmetric Alkylthio Branched Chain on Pentacyclic Small Molecular Acceptors Enables High Efficiency Organic Solar Cells

Oligomeric Semiconductors Enable High Efficiency Open Air Processed Organic Solar Cells by Modulating Pre-aggregation and Crystallization Kinetics

Optimized Charge Transport Channel Enables Thick-Film All-Small-Molecule Organic Solar Cells

Organic Solar Cells Using Oligomer Acceptors for Improved Stability and Efficiency

Efficient Organic Solar Cells Based on Low-Cost Pentacyclic Fused-Ring Small Molecule Acceptors with a Fill Factor over 80%

Small Molecule Acceptors with a Nonfused Architecture for High-Performance Organic Photovoltaics

P-doped All-Small-molecule Organic Solar Cells with Power Conversion Efficiency of 17.73%

15.71% Efficiency All‐Small‐Molecule Organic Solar Cells Based on Low‐Cost Synthesized Donor Molecules

19.0% Efficiency Binary Organic Solar Cells Enabled by Using a Building Block As Solid Additive

15.3% Efficiency All‐Small‐Molecule Organic Solar Cells Achieved by a Locally Asymmetric F, Cl Disubstitution Strategy

All‐Small‐Molecule Organic Solar Cells with Efficiency Approaching 16% and FF over 80%

Design of All-Small-Molecule Organic Solar Cells Approaching 14% Efficiency via Isometric Terminal Alkyl Chain Engineering

Efficient Large Area All‐Small‐Molecule Organic Solar Cells Fabricated by Slot‐Die Coating with Nonhalogen Solvent

Introducing Phenyl End Group in The Inner Side Chains of A‐Da'd‐A Acceptors Enables High‐Efficiency Organic Solar Cells Processed with Nonhalogenated Solvent

Small-Molecular Donor Based Efficient Organic Solar Cells with Thermally Stable Morphologies

Dimer Acceptor Adopting a Flexible Linker for Efficient and Durable Organic Solar Cells

High‐Performance All‐Small‐Molecule Organic Solar Cells Enabled by Regio‐Isomerization of Noncovalently Conformational Locks

Boosting efficiency and stability for organic solar cells by subtle management electron-withdrawing terminal of electron acceptors based on asymmetric dual-donor centra