Abstract:With the rapid development of modern electronic technology, addressing the heat dissipation problem of devices has become more and more urgent. Herein, the effects of molybdenum disulfide (MoS2) and hybrid hexagonal boron nitride (h-BN)/MoS2 fillers on the thermal conductivity of polydimethylsiloxane (PDMS) were investigated by reverse non-equilibrium molecular dynamics (RNEMD) simulation with fully atomistic model. Firstly, we simulated the thermal conductivity of MoS2 and BN fillers. It was found that the thermal conductivity of the two fillers enhanced with the increase of their sizes. The intrinsic thermal conductivity of MoS2 and BN obtained via the extrapolation were 52 W/(m·K) and 606 W/(m·K) separately. For 1-5 layers, the number of layers has almost no effect on the thermal conductivity of MoS2, but as the number of layers increase, the thermal conductivity of BN first decreases and then reaches a plateau. Then, we studied the thermal conductivity of the PDMS-based composites. Due to the existence of holes in the PDMS/MoS2 system, the thermal conductivity of PDMS/MoS2 composites is not much improved compared with that of PDMS. Therefore, we then introduced a hybrid BN/MoS2 filler into the composite to solve the void problem in the system. The results proved that this method was effective. The introduction of the hybrid BN/MoS2 filler effectively promoted the dispersion of the two fillers in the PDMS matrix and greatly reduced the holes in the composites. Compared with the composites filled with only one kind of filler, PDMS/BN/MoS2 composites possess better thermal conductivity. The most surprising finding is that there exists an optimal loading ratio of the two fillers, and the thermal conductivity of the composite reached the maximum when the mass ratio of the two fillers is approximately 1:1, attributed to the change of the volume fraction of holes(<math>Φ</math>). In addition, with the increase of hybrid BN/MoS2 filler content, the thermal conductivity of the composites is also increasing. The oscillating shear can also promote the orientation of the filler along the shear direction and improve the thermal conductivity of composites along that direction. Therefore, composites based on hybrid BN/MoS2 nano-fillers can be used to improve the thermal conductivity of insulating polymer materials. The findings should shed some light on the design and preparation of polymer composites with excellent thermal conductivity and electrical insulation properties.

Multi‐contact Hybrid Thermal Conductive Filler Al2O3@AgNPs Optimized Three‐dimensional Thermal Network for Flexible Thermal Interface Materials

Multi‐contact hybrid thermal conductive filler Al 2 O 3 @ AgNPs optimized three‐dimensional thermal network for flexible thermal interface materials

Enhanced the Thermal Conductivity of Polydimethylsiloxane via a Three-Dimensional Hybrid Boron Nitride@Silver Nanowires Thermal Network Filler

Fabrication of copper powder hybrid supported fillers with interconnected 1D/2D/3D nanostructures for enhanced thermal interface materials properties

Nano-capsuled thermal interface materials filler using defective multilayered graphene-coated silver nanoparticles

Synergistic Enhanced Thermal Conductivity of Polydimethylsiloxane Composites Via Introducing SCF and Hetero-Structured GB@rGO Hybrid Fillers

Improving through-plane thermal conductivity of PDMS-based composites using highly oriented carbon fibers bridged by Al2O3 particles

Effect of Surface Functionalization of Si3N4 Fillers on Thermal and Mechanical Properties of TIMs

Facile fabrication of three-dimensional thermal conductive composites with synergistic effect of multidimensional fillers

Achieving highly thermal conductivity of polymer composites by adding hybrid silver–carbon fiber fillers

A high-performance thermally conductive and electrically insulating silver@siloxane/graphene/epoxy composites at low filler content: Fabrication, mechanism study of insulation and thermal conductivity enhancement

Thermal Interface Materials with Sufficiently Vertically Aligned and Interconnected Nickel-Coated Carbon Fibers under High Filling Loads Made Via Preset-Magnetic-field Method

Synergistic effect of carbon fiber and alumina in improving the thermal conductivity of polydimethylsiloxane composite

Optimization of Effective Thermal Conductivity of Thermal Interface Materials Based on the Genetic Algorithm-Driven Random Thermal Network Model

Designing high thermal conductivity of polydimethylsiloxane filled with hybrid h-BN/MoS2 via molecular dynamics simulation

GMP/Al2O3/ZnO/PDMS thermal interface materials with anisotropic thermal conductivity and electrical insulation ability obtained by 3D‐printing method

Silver Nanoparticle-Enhanced Three-Dimensional Boron Nitride/Reduced Graphene Oxide Skeletons for Improving Thermal Conductivity of Polymer Composites

Enhanced thermal conductivity of epoxy composites via bridged Al 2 O 3 network with in situ formed silver nanoparticles

Particle packing theory guided multiscale alumina filled epoxy resin with excellent thermal and dielectric performances

Effect of segment structure of monotrimethoxysilylethyl-terminated asymmetric Polysiloxanes on the thermal management performance of AlN-filled silicone pastes

Strawberry Like Micro@nano Hybrid Filler for Thermally Conductive Epoxy Composites