Abstract:A wind turbine is a conversion mechanism that converts wind energy into electrical energy, but the conversion efficiency cannot reach 100%, so there is partial loss. These losses are converted into thermal energy, which in turn causes the wind turbine to heat up and affect generator performance. Therefore, the cooling and temperature field analysis of wind turbines is very important. In this paper, an electromagnetic analysis model is established by using the parameters of a 4 MW wind turbine; the losses of each part of the generator under rated load and three-phase short-circuit conditions are calculated, respectively; and the heat source is imported into the workbench fluent software to determine the cooling mode, so as to obtain the magnetic-thermal-flow field coupling model of permanent magnet synchronous direct drive wind turbine. The temperature distribution and temperature rise of the generator are obtained. Under the rated load condition, the overall maximum temperature rise of the wind turbine is 41.4 °C, about 180 mm near the fluid outlet side, which is as high as the winding temperature rises, because the winding is the main heating body. The maximum temperature rise of the rotor model and the permanent magnet model is about 36 °C. Under the three-phase short circuit condition, the temperature distribution of each component is similar to that under the rated load condition, and the temperature near the fluid inlet is low; the lowest is only 29.8 °C. The higher the temperature at the fluid's outlet, but not close to it, the higher the temperature is when it is about 180 mm away from the fluid's outlet side. The temperature difference in the same axial length is relatively large, with a maximum temperature difference of about 120 °C. The temperature distribution and temperature rise of the generator are independent of the operating conditions, which mainly affect the value. Additionally, through experimental verification, the minimum error under the rated load condition is 1.05%, the maximum error is 3.3%, and the average error is 2.30%. The minimum error under the three-phase short-circuit condition is 1.5%, the maximum error is 3.62%, and the average error is 2.26%. The difference with the engineering error range requirements is small, indicating the reasonable and effective effectiveness of this method. This study aims to provide a strong reference for analyzing the cooling and magnetic thermal flow field and a coupling analysis of direct drive wind turbines.

3D Lumped Parameter Thermal Network for Wound-Field Synchronous Generators

Enhanced Ventilation and Thermal Performance by Skewed Through Holes on Rotor Yoke in Forced Air-Cooled Permanent Magnet Wind Generators

Coupled field finite element analysis for turbine generator under loss-of-excitation asynchronous operation

3-D Eddy Current Analysis in the End Region of a Turbogenerator by Using Reduced Magnetic Vector Potential

Research on the Nonlinear Thermal-liquid Coupled Network Model of Whole Stator of Three-gorge Generator

3D finite element study of transient electromagnetic forces acting on the stator end-windings of a large turbo-generator

3D Eddy Current and Temperature Field Analysis of Large Hydro-Generators in Leading Phase Operations

The dynamic performance and temperature distribution of turbine generator under loss of excitation by using coupled FE analysis

Improving Combined Flow and Thermal Network Accuracy for Radially Air-Cooled Generators by Considering the Nonlinear Resistance Characteristics of T-Junction Flow

Thermal Optimization of a Totally Enclosed Forced Ventilated Permanentmagnet Traction Motor Using Lumped Parameter and Partial Computational Fluid Dynamics Modeling

Thermal Modeling of a High-Voltage Fault-Tolerant Wind Generator with HTS Bulks

Adaptive Thermal Model for Permanent Magnet Synchronous Machines of Vehicles

Thermal Analysis of Permanent Magnet Synchronous Motor under Different Working Conditions Based on Thermal Network

Thermal Analysis of High Speed Permanent Magnetic Generator

Thermal Analysis of Internal Short-Circuit Faults in Stator Windings of Multiphase Permanent Magnet Synchronous Generator with Rectifier-load System

Ac Loss Analysis on an Hts Field Winding of the Generator with T-A Formulation

A General Arc-Segment Element for Three-Dimensional Thermal Modeling

Calculation and Analysis of the Surface Heat-Transfer Coefficient and Temperature Fields on the Three-Dimensional Complex End Windings of a Large Turbogenerator

AC Loss Estimation on HTS Armature Windings for a 30-Kw Marine Generator Prototype

Simplified Mathematical Model of Inter-Turn Short Circuit of Field Windings in Hydro-Generators and Its Application

Research on Temperature Distribution of Large Permanent Magnet Synchronous Direct Drive Wind Turbine