Abstract:Calculation and experimental estimates of the residual life of steels P2M and EI415 of two strength levels (H and B) are carried out using two methods, the new one and the traditional. The loading was carried out for 300 thousand hours under conditions similar to those in which the metal operates in the zone of blade attachment in the rim of the disk of the first stage of medium-pressure rotors of K-300-240 LMZ and KhTZ turbines. When evaluating the residual life, a gradual decrease in stresses due to creep was taken into account by distinguishing several stages with conditionally constant stresses. According to the new methodology, the residual life was estimated by a change in the metal super-continuity at each stage 47 = ц/п + 1, where u/ is the continuity, n is the crack formation index; whereas in the traditional method the relative damage Р is estimated according to the principle of linear summation of damage (LSP). It is shown that the time dependences P and 47 obey the logarithmic law, while the metal of the fbrgings В (high strength) in all cases had a greater resource compared to the fbrgings H (low strength). For the first time, the process of resource depletion was considered by analyzing the sum of two functions: 47 + P = 1. It is shown that for R2M steel this amount is less than unity; for steel EI415 it is equal to or greater than unity. Proceeding from the literature data on the differences that follows from using LSP rule for a relatively viscous and brittle metal, we suggested that deviations from unity are attributed to the error in estimating the resource according to the LSP principle. Therefore, the result obtained by the new method should be recognized as more accurate. Taking into account the use of samples with a particularly deep sharp notch in which the brittle crack development is guaranteed by the proposed methodology, the new principle of calculating the residual life can be used in determination of the resource for any type of the parts made of the metal subjected to brittle fracture during operation under creep conditions.

Strain-life estimation of the last stage blade in steam turbine during low volume flow conditions

Structure and Modal Analysis of the Last Stage Blade in Steam Turbine under Low Volume Flow Conditions

Analysis on strength performance of the last stage blade in steam turbine under low mass flow conditions

ANALYSIS ON FLOW SEPARATION CHARACTERISTICS OF LAST STAGE BLADE IN STEAM TURBINE UNDER SMALL VOLUME FLOW CONDITION

Vibration characteristics and life prediction of last stage blade in steam turbine Based on wet steam model

Research on Vibration Characteristics of Last Stage Blade Based on Blade Tip-Timing Technology

Calculation of Finite Element of Thermal Stress and Analysis of Low-cyclic Fatigue Life for Non-central Hole Rotor of 135 MW Turbine

Fatigue life prediction of turbine blades with geometric imperfections made of stainless steel

The Effect of High-Speed Steam Discharged from the Bypass Diffusers on Low-Pressure Turbine Blades

Fatigue life prediction of mistuned steam turbine blades subjected to deviations in blade geometry

Study of cracks in the last-stage rotor blade of a steam turbine and the corrosion fatigue properties of its materials

Performance Prediction and Flow Analysis in the Vaned Distributor of A Pump Turbine under Low Flow Rate in Pump Mode

Analysis of Dynamic Stresses in Kaplan Turbine Blades

Study on Structure Dynamic Characteristics for Internal Components of Kaplan Turbine Runner under Different Contact Modes

A Study and Optimization of the Unsteady Flow Characteristics in the Last Stage Impeller of a Small-Scale Multi-Stage Hydraulic Turbine

Flow-Induced Vibratory Stress Prediction on Small Turbofan Engine Compressor Vanes Using Fluid-Structure Interaction Analyses

Hot Blade Shape Reconstruction Considering Variable Stiffness and Unbalanced Load in a Steam Turbine

THREE DIMENSIONAL VISCOUS FLOW NUMERICAL ANALYSIS OF STALL FLUTTER IN STEAM TURBINE BLADES

Stress Characteristics Analysis of Vertical Bi-Directional Flow Channel Axial Pump Blades Based on Fluid–Structure Coupling

Assessment of the residual life of the high-temperature elements of the turbine rotors through modeling the reduction of the metal continuity

Distribution Characteristics of High Wetness Loss Area in the Last Two Stages of Steam Turbine under Varying Conditions