Abstract:TiAl-based alloy have potential as high temperature structural materials for aerospace applications, especially for thermal protection systems in aerospace vehicles including skin materials. Unfortunately, the ductility and formability of TiAl-based alloys are rather poor and thus gamma-TiAl sheets or foils are quite difficult to be manufactured by traditional methods and still far from practical applications. In the present work, commercial pure Ti foils and in-house fabricated TiB2/Al composite foils were alternately stacked and rolled to prepare Ti-(TiB2/Al) laminates, and then heat treatment was utilized to make liquid Al react with solid Ti, and finally TiAl-based composite sheet with multi-layer distributed reinforcement TiB2 particles were achieved. This method avoided the direct deformation of brittle TiAl billets and thus the near-net-shape processing of TiAl-based alloys sheets was feasible. Phase transformation and microstructure evolution during heat treatment were investigated and mechanical properties of the resulting micro-laminated TiB2-TiAl composite sheets were evaluated. The results showed that porous TiAl3 layers were produced by the reaction between liquid Al and solid Ti because of Kirkendall effect, and the following densification treatment under 50 MPa at 1300 degrees C for 2 h significantly improved the relative density of material. Subsequently, the reaction diffusion between TiAl3 and residual Ti proceeded in the following heat treatment, and finally fully lamellar (alpha(2)-Ti3Al+gamma-TiAl) layers were obtained. TiB2 particles did not participate in any reaction and remained, and displayed multi layered distribution in the matrix (alpha(2)-Ti3Al+gamma-TiAl) layers. TiB2 rich layer hindered the coarsening of lamellar colony of (alpha(2)-Ti3Al+gamma-TiAl) layer. Tensile properties at 800 degrees C of multi layered TiB2 TiAl composite sheets remarkably increased because of an increase of energy dissipation caused by plastic deformation.

Electron Beam-Physical Vapor Deposited TiAl-based Laminated Composite Sheet with Nb Layer Toughening

Fabrication, Microstructure and Properties of Electron Beam-Physical Vapor Deposited Tial Sheet and Tial/Nb Laminated Composites

Fabrication of Fully Dense Tial-Based Composite Sheets with A Novel Microlaminated Microstructure

Investigation on the Microstructure and Mechanical Behaviors of a Laser Formed Nb-Ti-Al Alloy

Microstructures and Mechanical Properties of Laminated Structural Nb-Ti-Al Composites Fabricated by Laser Deposition

Research on Ti-Al/Nb Multilayer Composites Fabricated by EB-PVD

Microstructure and Mechanical Properties of Ti/Ti-Al Multi-layered Composite Prepared by EB-PVD

Phase composition and microanalysis of TiAl-based alloys sheet by electron beam-physical vapor deposition

Ti-48Al-2Cr-2Nb alloys prepared by electron beam selective melting additive manufacturing: microstructural and tensile properties

Electron Beam Welding and Post Heat Treatment of a New Near-Beta High-Strength Ti-4Al-5Mo-5V-5Cr-1Nb Alloy

In-situ synthesis of Al2O3-reinforced high Nb–TiAl laminated composite with an enhanced strength-toughness performance

Investigation of Ti2AlNb-Added TiAl Composite Prepared by Direct Laser Deposition

TiAl-BASED COMPOSITE SHEET WITH MULTI-LAYER DISTRIBUTED REINFORCEMENT PREPARED BY SOLID-LIQUID REACTION

Macro-microscopic Morphology and Phase Analysis of TiAl-based Alloys Sheet Fabricated by EB-PVD Method

Microstructure, Mechanical, and Tribological Properties of Nb-Doped TiAl Alloys Fabricated via Laser Metal Deposition

Microstructure and Mechanical Properties of Ti-Al-Ti-Ti2AlNb Laminated Composites Based on the Ductile-brittle Structure

Strengthening and toughening of laminated TiAl composite sheets by titanium alloy layers and carbide particles

Study on Microstructures and Mechanical Properties of Ti/Ti-Al Microlaminated Composite

Structure and Property Research on TiAl/NiCoCrAl Multilayer Composites Fabricated by EB-PVD

Fabrication, Microstructure, and Mechanical Property of NiAl-based Composite with Microlaminated Architecture by Roll Bonding and Annealing Treatment

Interface Characteristics and Mechanical Properties of a Ti–TiAl Laminated Composite