Abstract:High-strength, high-porosity and relatively low-shrinkage ZrO 2 ceramics were successfully fabricated by material extrusion 3D printing technology via optimizing CaCO 3 addition and sintering temperature. The effects of different CaCO 3 additions on the performance, phase formation, and microstructure of porous ZrO 2 ceramics sintered at different temperatures were systematically investigated and discussed. The results showed that flexural strength, porosity and shrinkage of the ZrO 2 ceramics were significantly affected by CaCO 3 addition and sintering temperature. The appropriate addition of CaCO 3 could promote sintering and phase transformation of m-ZrO 2 , increase the number and size of pores in the matrix. The corresponding flexural strength and porosity of the sintered samples increased, while the shrinkage rate decreased. The raised sintering temperature appropriately facilitated the formation of CaZrO 3 . Microstructural analysis indicated that CaZrO 3 exhibited a larger polyhedral bulk morphology, mainly distributed at the edges of pores, which could stabilize the pore structure and thicken the sintering necks, and thereby exhibiting well-balanced comprehensive performance. The ZrO 2 ceramics with high flexural strength, high porosity and relatively low shrinkage rate were achieved by adding 15 wt% CaCO 3 and sintering at 1450 °C. The resulting flexural strength and porosity were 27.33 MPa and 67.62 %, respectively, presenting an improvement of 563.35 % and 13.69 % compared to ZrO 2 ceramics without CaCO 3 . Moreover, the shrinkage rates in the X-direction (9.98 %), Y-direction (9.62 %), and Z-direction (9.94 %) significantly reduced, decreasing by 38.28 %, 38.10 %, and 41.46 %, respectively.

Creep Mechanism of Zircon-Added Silica Ceramic Cores Formed by Stereolithography

Enhancing creep resistance performance in silica-based ceramic core materials through shell-core structure

Fabrication of Silica-Based Ceramic Cores with Internal Lattice Structures by Stereolithography

Microstructure and properties evolution of silicon-based ceramic cores fabricated by 3D printing with stair-stepping effect control

Compositional optimization of high-solid-loading ceramic cores via 3D printing

Effect Of Silica Sol On The Properties Of Alumina-Based Duplex Ceramic Cores

Effect of Particle Size on Properties of Alumina-Based Ceramic Cores

3D Printed Zirconia Ceramics Via Fused Deposit Modeling and Its Mechanical Properties

Alumina-Based Ceramic Core Nano-Composites For Investment Casting

R-curve of La2O3 doped Zirconia Toughened Alumina Composites Prepared via Stereolithography based 3D Printing

Effect of Al(OH) 3 on the Properties of Silica-based Ceramic Cores Prepared by Laser Powder Bed Fusion Combined with Vacuum Infiltration

Influence of Al2O3 Fiber on the Properties Al2O3-Based Ceramic Core

Fabrication of High-Performance Al2O3-ZrO2 Composite by a Novel Approach That Integrates Stereolithography-Based 3D Printing and Liquid Precursor Infiltration

Influence of debinding parameter and nano-ZrO2 particles on the silica-based ceramic cores fabricated by stereolithography-based additive manufacturing

Achieving high-strength, high-porosity and relatively low-shrinkage in extrusion-based 3D printed ZrO 2 ceramics by adjusting CaCO 3 addition and sintering temperature

The Rising Crack Resistance Curve Behavior and Mechanism of La2O3 Doped Zirconia Toughened Alumina Composites Prepared Via Vat Photopolymerization Based 3D Printing

Fused silica ceramic core based on network-structured zircon design via 3D printing

Effect of synergism of solid loading and sintering temperature on microstructural evolution and mechanical properties of 60 vol% high solid loading ceramic core obtained through stereolithography 3D printing

Improved creep resistance of single-phase (Ti,Zr)(B,C) ceramics by solute-induced restraint of dislocation movements on basal plane

Influence of Al2O3 content on mechanical properties of silica-based ceramic cores prepared by stereolithography

Improved mechanical properties of SiB6 reinforced silica-based ceramic cores fabricated by 3D stereolithography printing