Abstract:MgO–CaO composites are basic materials with high melting points, high chemical resistance to alkaline environments, clean steel production, environmental friendliness, and abundant sources. In the current work, carbon nanofibers (CNFs) with diameters between 150 to 270 nm were prepared at different temperatures (up to 1200 °C) by carbonization of electrospun polyacrylonitrile (PAN) precursors. Then, the MgO–CaO composites were prepared in two steps. First, 3 wt% CNFs carbonized at different temperatures were added to the composite to determine the optimal carbonization temperature. Subsequently, the physical properties (apparent porosity and bulk density) and mechanical properties (flexural strength (FS) and cold crushing strength (CCS)) of the MgO–CaO-CNF composites were investigated. X-ray diffraction (XRD), Raman spectroscopy, field emission scanning electron microscopy (FESEM), Energy-Dispersive X-ray spectroscopy (EDS), and thermogravimetric analysis (TGA) were used to analyze the composition, morphology, and structure of the CNFs powders and composite samples. Based on the results obtained, such as the percentage graphitization, length, average diameter, and morphology of the CNFs, 1000 °C was determined as the appropriate carbonization temperature for the next steps of this study. In a second step, the CNFs synthesized at 1000 °C were added to the MgO–CaO with different wt% (0, 0.5, 1, 1.5, 2, 2.5, and 3 wt%). It was found that by adding CNFs (up to 1.5 wt%) into the MgO-CaO composites, the physical properties increased due to the improvement of densification, and mechanical properties improved due to the activation of reinforcing mechanisms, the reduction of surface defects and the creation of a dense body. However, these properties decreased from 1.5 to 3 wt% due to the agglomeration and poor dispersion of the CNFs. Finally, the results illustrated that adding CNFs, even in small amounts, significantly improved the features of MgO-CaO compounds; the ideal content was 1.5 wt% CNFs.

In Situ Transformed Carbon Fibers/Al2O3 Nanocomposites Using Cao–MgO–SiO2 Sintering Agent

Properties of Carbon Nano-Tubes–cf/sic Composite by Precursor Infiltration and Pyrolysis Process

Effects of in situ formed nanostructures on the structure and properties of C/SiOC composites

Structure and properties of fine diameter continuous SiC ceramic fiber reinforced Al matrix composites

Ordered Mesoporous SiOC and SiCN Ceramics from Atmosphere-Assisted in Situ Transformation

3C-SiC Nanowires In-Situ Modified Carbon/Carbon Composites and Their Effect on Mechanical and Thermal Properties

Microstructure and Mechanical Properties of Multiphase Strengthened Al/Si/Al 2 O 3 /SiO 2 /MWCNTs Nanocomposites Sintered by In Situ Vacuum Hot Pressing

Effectively enhanced strength by interfacial reactions in in-situ carbon reinforced Al matrix composites

Slurry‐impregnating hot‐press sintered silicon carbide nanofiber/silicon carbide composites with Al‐B‐C as sintering additives

Effect of carbon nanofibers fabricated from electrospun PAN precursors on the characteristics and Densification of MgO–CaO Ceramic systems

In-situ Preparation of Nano MoSi 2 SiC Composite by Melt Infiltration of Silicon Method

Preparation and mechanical behaviors of multiscale SiC nanowires/carbon fiber reinforced silicon oxycarbide ceramic composites

In situ formation of Si3N4–SiC nanocomposites through polymer-derived SiAlCN ceramics and spark plasma sintering

Fabrication of C/SiC composites by siliconizing carbon fiber reinforced nanoporous carbon matrix preforms and their properties

Effects of in situ Mg-Sialon and β-Sialon on the microstructure and properties of MgAl2O4-SiC composites

Effect of In-situ Transformed Pre-oxidized Polyacrylonitrile Fibers on the Microstructure and Mechanical Properties of TiCN-based Cermets

Mechanical Properties of Al Matrix Composite Enhanced by In Situ Formed SiC, MgAl2O4, and MgO via Casting Process

Study on the mechanical properties and microstructure of Al2O3/nano-SiC multiphase ceramics

Preparation of in-situ grown carbon nanotubes via dithiocarbamate in composites with excellent microstructure and mechanical performance

Microstructure and Mechanical Properties of Al<sub>2</sub>O<sub>3</sub>/SiC Nanocomposites Prepared by SPS

Fabrication, microstructure, and mechanical properties of all-oxide ceramic matrix composites using high-yield precursors