Abstract:In this study, the in-situ compatibilization reaction between recycled acrylonitrile-butadiene-styrene copolymer (rABS) and functional styrene-ethylene-butylene-styrene block maleic anhydride (SEBS-g-MAH) was confirmed, which contributed to the toughening phenomenon of rABS, especially the notched impact strength. As mechanical test that manifested, the rABS/SEBS-g-MAH blends are stronger and more ductile than the rABS/SEBS blends. Prominently, the former has great advantage over the latter in terms of improving the impact performance. Scanning electron microscope (SEM) images showed that the compatible segments that were generated by reaction not only improve the interface adhesion of rABS/SEBS-g-MAH blends but also promote the evolution of co-continuous structures, which can be evidently observed after etching. Furthermore, the SEM micrographs of tensile fracture surfaces indicated that the formation of the co-continuous phase and the improvement of interface adhesion are the most profound reasons for the excellent tensile properties of the rABS/SEBS-g-MAH blends. The impact fracture surface revealed that two-phase interface affects crack propagation and shear yielding absorbs more impact energy than simple interface debonding does at higher deformation rates. Meanwhile, rheological analysis demonstrated that the complex viscosity of the rABS/SEBS-g-MAH (80/20 wt%) blend with a co-continuous structure exhibits a maximum positive deviation at low frequencies from the theoretical value calculated using the rule of logarithmic sum, which indicated a connection between co-continuous structure and complex viscosity. In addition, the storage modulus vs. loss modulus curves of the blends revealed that the viscoelastic behavior of rABS/SEBS-g-MAH blends is very similar to that of rABS.

Study on Properties and Stress Relaxation Behavior of Oil‐extended SBS/LLDPE/EVA Blends

Structure-property Relationships of Reactively Compatibilized PHB/EVA/starch Blends.

Synthesis, characterization and lubricating effect of long chain branched polydimethylsiloxane-g-polyethylene copolymers

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Influence of Crosslinking on Crystallization, Rheological, and Mechanical Behaviors of High Density Polyethylene/ethylene‐vinyl Acetate Copolymer Blends

Effect of styrene-ethylene-butadiene-styrene and its synergetic effect with ethylene vinyl acetate on the mechanical, thermal, dielectric, and water-treeing behaviors of crosslinked polyethylene

Mechanical And Rheological Properties Of Lldpe/Hdpe, Lldpe/Eva Blends

Blends of rABS and SEBS: Influence of In-Situ Compatibilization on the Mechanical Properties

Study on Rheological Properties and Relaxational Behavior of Poly(dianilinephosphazene)/low-Density Polyethylene Blends

Injection molding and shear‐induced stress simulation of poly (styrene‐ethylene‐butylene‐styrene) and polypropylene blends

Rheological Properties and Morphological Evolutions of Polypropylene/Ethylene-Butene Copolymer Blends

Study on the Morphology, Mechanical, Thermal Stability Properties of Poly(Lactic-Acid)/Poly(Ether-Block-Amide) Blends Prepared by Triple-Single Screw Extruder

Preparation and Properties of LLDPE/PMVS Blends

Dynamic Mechanical Properties and Morphology of High‐density Polyethylene/caco3 Blends with and Without an Impact Modifier

EVA and SEBS-MA copolymers incorporated silicone rubber/SEBS blends: improvement of mechanical and thermal properties

Reinforcing and Toughening Modification of poly (3-hydroxybutyrate-co-3-hydroxyvalerate)/ethylene-vinyl Acetate Copolymer (PHBV/EVA) Blends Compatibilized by Benzoyl Peroxide

Study on Processability and Mechanical Properties of SEBS/HDPE Blend

CRYSTAF, DSC and SAXS Study of the Co-Crystallization, Phase Separation and Lamellar Packing of the Blends with Different Polyethylenes

Use of crosslinking agent to produce high‐performance PLA/EVA blends via reactive processing

Research on Poly(lactic acid)/Poly(butylenes succinate) Blends

Mechanical, thermal and degradation properties of poly(d,l-lactide)/poly(hydroxybutyrate-co-hydroxyvalerate)/poly(ethylene glycol) blend