Abstract:Solar cavity receiver is a vital component in a solar power tower (SPT) system, where concentrated solar irradiation is absorbed, converted into heat and carried away by a kind of heat transfer fluid. The cavity receiver usually suffers from the high-flux and non-uniform concentrated solar irradiation, which would cause local overheating, large temperature gradient and even thermal stress fracture of the receiver and bring challenges for the safety of its daily operation. Therefore, it is necessary to investigate the thermal and mechanical performance of the solar cavity receiver. In the present study, a superheated water/steam solar cavity receiver with three boiling panels and a superheater was chosen as the physical model. An integrated simulation method, which couples the Monte-Carlo ray tracing (MCRT) method, the appropriate heat transfer correlations, the finite volume method (FVM) and the finite element method (FEM), was employed to simulate the complicated heat transfer process inside the receiver and conduct the thermal stress analysis for the absorber panels. With this method, the three-dimensional wall temperature and thermal stress distributions were gained both on the boiling panels and the superheater, and the causes of thermal stress induced by different temperature gradients were analyzed in detail. The following results were obtained: 1) The heat flux, wall temperature and equivalent thermal stress distributions all appear highly non-uniform on the absorber panels; 2) The hot spots can be found on the membrane wall between the elbows of the boiling panels, which can easily generate the high thermal stress due to the large temperature gradient with their surroundings; 3) The bi-axial stress at the outer and inner radius of the boiling tubes can be created by the large radial temperature gradient, and the thermal stress varies as a cosine distribution across the circumference of the superheated tubes, which is induced by the large temperature gradient in the circumferential direction. Besides, the spot-like areas with high thermal stress can also be found on the superheated tubes due to the considerable nonlinear axial temperature gradient. Moreover, the thermal stress on the membrane wall connected with both the boiling and the superheated tubes has the definite directionality, which shows parallel to the tubes or perpendicular to the tubes; 4) The thermal stress concentration always occurs at the high-temperature and structural discontinuity locations. Here, the thermal stress of the superheater is 360 MPa higher than that of the boiling panels. In general, the superheater has both the higher wall temperature and thermal stress, which is more crucial for the safe operation of the superheated water/steam solar cavity receiver.

Non-uniform and Volumetric Effect on the Hydrodynamic and Thermal Characteristic in a Unit Solar Absorber

Effect Evaluation of Micro/nano Structured Materials on the Performance of Solar Thermophotovoltaic System: an Analysis Based on Measurement Data

Effect of pore size and porosity distribution on radiation absorption and thermal performance of porous solar energy absorber

Analysis on the Effects of Different Receiver Structures and Porous Parameters on the Volumetric Effects and Heat Transfer Performance of Porous Volumetric Solar Receiver

An Optimized Model and Test of the China'S First High Temperature Parabolic Trough Solar Receiver

Thermo-mechanical performance enhancement of volumetric solar receivers using graded porous absorbers

Numerical Study on Thermal Performance of a Solar Cavity Receiver with Different Depths

Numerical Investigation on Uniformity of Heat Flux for Semi-Gray Surfaces Inside a Solar Cavity Receiver

Effects of Absorber Emissivity on Thermal Performance of a Solar Cavity Receiver

An Efficient 3D Tube-Level Flux-Thermal Model of External Tubular Receivers in Solar Power Tower Systems

Experimental and numerical study on the reflectance losses of the porous volumetric solar receiver

Study on Heat Transfer and Stress Characteristics of the Pressurized Volumetric Receiver in Solar Power Tower System

Convective heat transfer characteristics of supercritical CO 2 in mini-channels of compact solar receivers under unilateral heating conditions

Reticulated Porous Volumetric Solar Receiver Designs Guided by Normal Absorptance and Hemispherical Volumetric Emittance Investigations

Thermal-fluid-mechanical analysis of tubular solar receiver panels using supercritical CO2 as heat transfer fluid under non-uniform solar flux distribution

Thermal Characteristics and Thermal Stress Analysis of a Superheated Water/steam Solar Cavity Receiver under Non-Uniform Concentrated Solar Irradiation

Performance Bounds of Nanoparticles Laden Volumetric Absorption Solar Thermal Platforms in Laminar Flow Regime

Influence of Channel Depth on the Performance of Solar Air Heaters

A theoretical heat transfer analysis of different indirectly-irradiated receiver designs for high-temperature concentrating solar power applications

Numerical Investigation on Porous Media Heat Transfer in A Solar Tower Receiver

Experimental study of photothermal conversion of heat absorbers filled with metal foams of different pore densities