Abstract:The use of high strength low alloy steels provides several potential advantages including lower weight, lower manufacturing costs, and ease of handling and transport. The progress in steel manufacturing technology has continually called for new developments in welding processes and consumables to produce weld metal deposits with mechanical properties essentially equivalent to the base metal. Controlling the weld metal microstructures as well as raising the welding productivity is critical factor for the development of weld metal of high strength steel to secure satisfactory mechanical properties and to reduce production costs. In order to meet the demand to apply 1000 MPa class steel to the fabrication of large scale steel structures, a weld wire for the 1000 MPa class steel has been under development to obtain the required strength and toughness, which depend primarily on the microstructure. In this work, the effects of shielding gas composition on the microstructure and properties of 1000 MPa grade deposited metals produced by metal active gas (MAG) welding have been investigated. The shielding gas employed was a mixture of argon (Ar) and carbon dioxide (CO2) (5%similar to 30%), and the weld heat input was 13 kJ/cm. The properties of deposited metal with shielding gas of 80%Ar+20%CO2 is the best, the yield strength is 980 MPa, meanwhile, its Charpy absorbed energy at room temperature and -40 degrees C are 72.6 and 52 J, respectively. The results show that the microstructure of the deposited metal, consisting primary of low carbon martensite and a few parallel bainite plate, became more interweaved bainitic packets as the CO2 content of the shielding gas was increased. The initial bainite nucleated at austenite grain boundaries and subsequent bainite plates can form at the oxide inclusions of intragranular, which presented an intersected configuration and the microstructure was refined. The content of bainite palte and distribution morphology of martensite/bainite is the intrinsic reason attributed to mechanical properties of deposited metals. The content of bainite for deposited metal has an optimal proportion and more isn't necessarily better. It was also found that the area fraction, the size and the compositions of oxide inclusions in deposited metals were changed with increasing CO2 content. The deposited metal as using 70%Ar+30%CO2 has the minimum toughness because more large size oxide inclusions formed which are known to be harmful to the toughness.

Gas Tungsten Arc Welding Assisted Droplet Deposition Manufacturing of Steel/lead Bimetallic Structures

Microstructural evolution and mechanical properties in the partial transient liquid phase diffusion bonding of tungsten to steel

Growth of Lead-Free Welding Films on Ferrite Substrate by Magnetron Sputtering

Interface Behaviors and Mechanical Properties of Diffusion Bonded 45 Steel/additive Manufactured 316L Steel Joints

Influence of Shielding Gas Composition on Microstructure Characteristics of 1000 MPa Grade Deposited Metals

Characteristics of TIG arc-assisted laser welding–brazing joint of aluminum to galvanized steel with preset filler powder

EFFECT OF SHIELDING GAS ON MICROSTRUCTURE AND PERFORMANCE OF 1000 MPa GRADE DEPOSITED METALS

Stable bonding of W and ODS steel fabricated by TLP diffusion technology through inserting a novel composite interlayer Zr/Cu

Microstructure Heterogeneity and Mechanical Properties of a High-Strength Ductile Laminated Steel by Electron Beam Welding

Wire arc direct energy deposited multiphase steel through in situ micropowder alloying: mechanical and metallurgical studies

Integrated laser additive manufacturing of high-strength steel and Ti6Al4V: Experimental investigations and thermodynamic calculations

Tungsten/steel diffusion bonding using Cu/W–Ni/Ni multi-interlayer

A novel molten wire tungsten inert gas welding process

Microstructure evolution and mechanical properties in a gas tungsten arc welded Fe42Mn28Co10Cr15Si5 metastable high entropy alloy

Tailoring droplet transfer and molten pool flow during hybrid laser arc welding of nickel base alloy

Interfacial Microstructural Characterization of Ti/Al Joints by Gas Tungsten Arc Welding

Microstructure and Tensile Strength of the Bonded Interfaces and Parent Materials in W/ODS Steel Joints Fabricated by Direct SSDB

Offset impacting of a liquid aluminum droplet train on a molten pool on a horizontally moving substrate during TIG-assisted droplet deposition manufacturing

Interface Microstructure and Numerical Simulation Investigations of Ni/TC18 Composite Tube Fabricated by Explosive Welding

Effects of laser printing parameters on molten pool formation, microstructure evolution and mechanical properties of laser directed energy deposition of difficult-to-process tungsten heavy-alloy

Microstructure, properties, and formation mechanisms of tungsten/steel hot isostatic pressing diffusion bonding joint utilizing a Ni-Si-B interlayer