Abstract:It is well known that lubricating oils reduce the friction coefficient between two surfaces in contact. Since petroleum lubricants are toxic and have a low biodegradability, they are typically not appropriate for the environment. As a result, as public worries about a pollution-free environment grow, so does the demand for lubricants that are acceptable to the environment. The primary rationale for utilizing vegetable oils in forthcoming bio-lubricant formulations is their high lubricating performance, low toxicity, sustainable, and biodegradability. Plant oils hold great potential as a foundational fluid for bio-lubricants, since their synthetic and vegetable oil-based esters provide the most environmentally friendly option for creating lubricants. In this study, Jatropha and Jojoba raw oil were chemically modified via epoxidation followed by transesterification to produce bio-lubricants. Thus, the aim of this work is to develop a bio-lubricant from jatropha and jojoba methyl ester, further adding nanoparticles multiwalled nanotubes and titanium dioxide for improvement of tribological properties. The chemical modification of the jatropha and jojoba oil results in a decrease in iodine value, resulting in the breaking of carbon bonds. Viscosity tests were performed using the Anton Par MCR 92 Rheometer, with temperature ranging from 30°C to 80°C. Thermal stability measurements of bio-lubricants were performed using PerkinElmer's Thermogravimetric analyzer − 4000 instrument and thermal degradation temperature for Epoxidized Jatropha – sulfuric acid, Epoxidized Jatropha – hydrochloric acid, Epoxidized Jojoba – sulfuric acid and Epoxidized Jojoba – Hydrochloric acid samples are 238°C, 224°C, 230°C, and 244°C, respectively. The 94.68% and 79.85% reduction in wear was obtained for Epoxidized Jojoba with hydrochloric acid, titanium dioxide and epoxidized Jatropha with sulfuric acid, multiwalled carbon nanotubes in comparison with their epoxidized samples. The coefficient of friction of Epoxidized Jatropha with sulfuric acid, multiwalled carbon nanotubes and Epoxidized Jojoba with Hydrochloric acid, Titanium dioxide sample was found to be 0.061 and 0.059, respectively.

The Lubrication Performance and Viscosity Behavior of Castor Oil under High Temperature

Research Progress of Lubricant Oxide Films in a Wide Temperature Range

Tribological Characteristics of Silicon Nitride-chilled Cast Iron with Oil-less Lubrication

Lubricating Properties of the Aqueous Solution of Castor Oil Polyoxyethylene Ether

Lubricity and Adsorption of Castor Oil Sulfated Sodium Salt Emulsion Solution on Titanium Alloy

Mechanism of superlubricity of a DLC/Si3N4 contact in the presence of castor oil and other green lubricants

Effect of Temperature on Rheological Behaviors and Tribological Properties of Nano-silica Greases Prepared from Base Oils with Different Viscosities

Sliding Wear of Cast-Iron Coatings and Cast-Iron-cast-iron Pairs in Lubricated Contact

High temperature lubrication performance of chlorophenyl silicone oil

Friction-reducing and anti-wear properties of 3D hierarchical porous graphene/multi-walled carbon nanotube in castor oil under severe condition: Experimental investigation and mechanism study

A Comparative Analysis of the Lubricating Performance of an Eco-Friendly Lubricant vs Mineral Oil in a Metallic System

Comparative tribological investigation of castor oil and its transesterified and aminolyzed derivatives

High temperature solid/liquid lubrication behaviours of DLC films

Evaluation of Aromatic Organic Compounds as Additives on the Lubrication Properties of Castor Oil

Effects of Lubricants on Friction and Wear of Ti(Cn)/1045 Steel Sliding Pairs

Tribological performance of silicone oil based Al2O3 nano lubricant for an Mg alloy subjected to sliding at elevated temperatures

Tribological Characteristics and Degradation Mechanism of Typical Synthetic Lubricants from Room Temperature to 300 °C

Tribological evaluation of date seed oil and castor oil blends with halloysite nanotube additives as environment friendly bio-lubricants

Effect of Temperature on Tribological Properties of Tial Based Self-Lubricating Composites

Characterization of bio-lubricants with nanoparticles additives

Static friction measurement methodology for the assessment of performance of industrial valves at high temperatures: Case study for a nickel-based alloy coating