Abstract:Microstructure, mechanical and corrosion properties of hot-extruded Mg-2.0Zn-0.4Mn with varying Al addition were investigated in this study. The results demonstrate that adding Al to Mg-2.0Zn-0.4Mn promotes dynamic recrystallization significantly during hot extrusion and improves the tensile mechanical properties and corrosion resistance of the hot-extruded alloy. The dynamic recrystallized grain sizes decrease while the fraction of dynamic recrystallization area increases with Al addition. This is owing to the promoted recrystallization nucleation rates attributed to the grain refinement or increased amount of grain boundaries in solutionized alloy and particle stimulated nucleation by undissolved second-phase particles. The quantity and size of second phase particles of extruded alloys also increase with Al addition, which, in turn, contributes to the refinement of recrystallized grains by grain boundary pinning effect. As a result, tensile properties of the extruded alloy have improved by alloying with Al, owing to the coupling effects of more solute atoms, reduced recrystallized grain size and presence of fine second-phase particles. The improved corrosion resistance of extruded alloys by Al addition is mainly attributed to Al solute atoms and relatively uniform extruded microstructure that facilitate the formation of a more compact passive film. However, galvanic corrosion induced by second-phase particles and the Mg matrix significantly mitigates this effect. Consequently, optimized Al addition to this extruded Mg-2.0Zn-0.4Mn alloy is determined to be 4 wt.%.

Effect of Extrusion on Mechanical Properties and Corrosion Behavior of Mg-Zn-Sn-Al Alloy

Effect of extrusion on mechanical properties and corrosion behavior of Mg-Mn-Zn alloy

Effect of Hot Extrusion on Corrosion Resistance of Mg-Zn-Y Alloy

Investigation on corrosion behavior and mechanical properties of an extruded Mg-Zn-Al-Sn-Mn alloy

Effect of Extrusion on Mechanical Property, Corrosion Behavior, and In Vitro Biocompatibility of the As-Cast Mg-Zn-Y-Sr Alloy

Effect of Extrusion Process on Microstructure, Corrosion Properties, and Mechanical Properties of Micro-Alloyed Mg–Zn–Ca–Zr Alloy

Effect of Al Addition on Microstructure, Mechanical, and Corrosion Properties of Hot Extruded Mg-2.0Zn-0.4Mn Alloy

Effect of Hot Extrusion on the Microstructure, Mechanical Properties, and Corrosion Behavior of Mg–11Li–3Al–2Zn–1.5Nd–0.2Zr Alloy

Comparative Study on Corrosion Behavior of As-Cast and Extruded Mg–5Y–7Gd–1Nd–0.5Zr Alloy in 5% NaCl Aqueous Solution

Effect of Sn Addition on Microstructure and Corrosion Behavior of As-Extruded Mg–5Zn–4Al Alloy

Microstructure and Corrosion Behavior of As-Extruded Mg-6.5Li-xY-yZn Alloys

Effect of Microstructures and Textures on Different Surfaces on Corrosion Behavior of an As-Extruded ATZ411 Magnesium Alloy Sheet

Effect of Microstructure on the Corrosion Behavior of as-cast and Extruded Mg–Sn–Y Alloys

Effect of extrusion process on microstructure and mechanical and corrosion properties of biodegradable Mg−5Zn−1.5Y magnesium alloy

Corrosion behavior and mechanical properties of extruded low-alloyed Mg−0.5Bi−0.5Y−0.2Zn alloy

Effect of extrusion on the microstructure and corrosion behavior of Mg-Zn-Mn-(0, 1.5)Sr alloys in Hank’s solution

Effects of Zn on Microstructure, Mechanical Properties and Corrosion Behavior of Mg–Zn Alloys

Effects of Extrusion Ratio on Microstructure, Mechanical and Corrosion Properties of Biodegradable Mg–Nd–Zn–Zr Alloy

Effect of Solid Solution Zn Atoms on Corrosion Behaviors of Mg-2Nd-2Zn Alloys

Effect of Zn on Mechanical Properties and Corrosion Properties of As-Cast Mg-Mn Alloy

Effect of Cooling Method on Microstructures and Mechanical Properties of Extruded Mg-4.4Zn-0.3Zr-0.4Y Alloy