Abstract:This study achieves combustion applications of methanol-diesel dual-direct injection in a retrofitted diesel engine by investigating methanol sprays and engine performance/emissions. Methanol draws high attention due to its green production potential and ease of adaptation to existing combustors and supply infrastructure. One of the most promising methods for utilising methanol in diesel engines is the dual direct injection, which provides a wide operating range and flexible injection control. This study provides an effective solution for dual direct injection by implementing a nozzle cap idea, which can mount a conventional direct injector for methanol delivery in an existing diesel engine. The custom-made nozzle cap can provide hole orientation variations, which effectively controls the methanol-air mixture distributions within the piston bowl. To this end, methanol sprays formed through the three-hole nozzle cap are analysed for varied injector pressure of 15 ∼ 35 MPa. High-speed schlieren imaging confirmed working of the new nozzle for methanol injection with expected results of increased liquid penetration length and cone angle for higher injection pressure. The spray images also helped understand how the mixtures would be distributed within the piston bowl due to direct injection. Experiments performed on a 1-litre single-cylinder common-rail diesel engine operating at 1400 rpm, up to 70 % methanol energy fraction and a broad range of methanol injection timings of BDC to TDC, showed that the methanol-diesel dual direct injection combustion produces overall lower power output than the diesel baseline due to lower calorific value and flame temperature of methanol but significantly reduced CO 2 emissions by up to 16 % and very low smoke emissions. The results showed high sensitivity to methanol injection timings and energy fraction in terms of the measured pressure, derived heat release rate and produced power due to an increase in mixture homogeneity for earlier injection timings and stratified charge conditions for later injection timings. However, the nozzle orientation change and expected methanol-air mixture distributions showed no measurable impact on pressure and heat release rate as well as engine power output and combustion stability. The most significant impact of the methanol three-hole nozzle orientation and resulting mixture distributions was found from uHC and NO x emissions because a nozzle orientation directing methanol more towards the corner of the piston bowl opposite side of the injector led to increased liquid wall wetting and methanol in crevice volumes and thereby causing less complete combustion for higher uHC and lower NO x . The low sensitivity of methanol mixture distributions to the in-cylinder pressure and engine power output but the measurable impact found on uHC and NO x emissions empathies the required optimisation of methanol direct injector nozzle depending on the combustion chamber design of the base diesel engine.

Influence of Diesel Oil/Methanol Compound Combustion Function on Diesel Engine Performance

Combustion and Emission Characteristics of a DI Diesel Engine Fueled by Diesel-Methanol Blends

Engine Performance and Emissions of A Compression Ignition Engine Operating on the Diesel-Methanol Blends

Study on Combustion Characteristics of a DI Diesel Engine Operating on Diesel/Methanol Blends

The Study on Preparation and Combustion of Diesel-Methanol Micro-Emulsified Fuel

Effects of Methanol Addition on the Combustion Process of the Methanol/Diesel Dual-Fuel Based on an Optical Engine

Numerical Study of the Effect of Direct-Injection Timing of Methanol and Excess Air Ratio on the Combustion Characteristics of a Marine Diesel-Methanol Dual-Fuel Engine

Experimental study on the effects of water addition in methanol on the performance of diesel-methanol diffusion combustion on a high-speed engine

Combustion and Emission Characteristics of Methanol–Diesel Dual Fuel Engine at Different Altitudes

The Effect of Methane Addition on the Low-Temperature Oxidation Preparation and the Thermal Ignition Preparation of Dimethyl Ether under Representative Engine In-Cylinder Thermal Conditions

Research on Fuel Spray Characteristics of Coal-Made Fisch-Tropsch Process Diesel/methanol

Diesel/methanol dual-fuel combustion: An assessment of soot nanostructure and oxidation reactivity

To achieve high methanol substitution ratio and clean combustion on a diesel/methanol dual fuel engine: A comparison of diesel methanol compound combustion (DMCC) and direct dual fuel stratification (DDFS) strategies

Effects of Diesel Pre-Injection Time on Combustion Process and Emission Characteristics of Diesel/Methanol Dual Fuel Engine

Effects of Injection Parameters and EHN Mixing on the Combustion Characteristics of Fueling Pure Methanol in a Compression Ignition Engine

Effect of injection strategy on a diesel/methanol dual-fuel direct-injection engine

Study on Particulate Structure Characteristics of Diesel Engines Fueled with a Methanol/Biodiesel Blend

Influence of methanol gasoline blend fuel on engine and catalyst performance

Experimental Investigation of Diluents Components on Performance and Emissions of a High Compression Ratio Methanol SI Engine

Effect of three-hole nozzle orientations on sprays and combustion in methanol-diesel dual direct injection engines

A comparative study on operating range and combustion characteristics of methanol/diesel dual direct injection engine with different methanol injection timings