Abstract:Recent research using the semicircular bending (SCB) test with 100 mm diameter specimen cored from gyratory compacted samples demonstrated the suitability of this sample size for testing dense graded asphalt mixes with a nominal maximum aggregate size (NMAS) of up to 19 mm. Alongside the gyratory compactor, the Marshall compactor remains part of current specifications in many countries, including ASTM international standards. The Marshall compactor uses a 4-inch (101.6 mm) mould, which is slightly larger than the gyratory compactor's 100 mm mould, and employs a different compaction effort, resulting in different aggregate orientation. This study investigates potential differences in the fracture properties of SCB test specimens compacted using different methods. Sample thicknesses of 30 , 40 , and 50 mm were evaluated in the SCB test at 25°C under a monotonic loading rate of 1 mm/min. A total of 81 specimens were prepared from three asphalt mixes with NMAS of 14 mm and 20 mm, including two dense graded asphalt mixes and one stone mastic asphalt mix. The fracture properties, including fracture energy, fracture toughness, and cracking resistance index (CRI) were evaluated. The study found that the repeatability, evaluated via the coefficient of variation, ranged from 1.1% to 21.7%, with an average value of 8.3%. A directly proportional relation was observed for indexes from the 100 mm and 150 mm samples using the gyratory compactor. The Marshall compactor specimens yielded higher fracture toughness and fracture energy values, while the CRI values were approximately 1.23 times those obtained from the gyratory compactor. This result shows that different compaction methods have direct effect on the fracture properties of SCB test specimens, emphasising the importance of considering compaction methods for the SCB test when determining the threshold value of cracking resistance for asphalt mixes, especially in the balanced mix design for asphalt mixes.

Study on mechanical properties of AR-SAMI

Experimental Study on the Anti-Cracking Performance for High Viscoelastic Asphalt Sand with SCB

Evaluation of Test Methods for Fracture Resistance of High Modulus Asphalt Binders from Rheological and Mechanical Perspectives

Evaluation of Asphalt Rubber Membrane Interlayer (ARMI) Using the University of Florida's Composite System Interface Cracking (CSIC) Test

Rheological Behavior of High Modulus Asphalt Binder and Its Indication for Fracture Performances

Effects of an Asphalt Rubber Membrane Interlayer on Pavement Reflective Cracking Performance

Analysis on Anti-cracking Performance of High Viscoelastic Tar Sand

Research on the Anti-Cracking Performance of High Viscoelastic Tar Sands

Comprehensive Laboratory Evaluation of Crack Resistance for an Asphalt Rubber Stress-Absorbing Membrane Interlayer (AR-SAMI)

Cohesive Cracking Simulation of Asphalt Mixture with Reflective Crack Through Xfem

Comparative Analysis of Rheological and Microscopic Performance of SBS Modified Asphalt Based on Field Aging and Laboratory Aging

Research On The Crack Resistance Of The High-Viscosity Emulsified Asphalt Sand Seal

Experimental Study on Pavement Performances of SBP Modified Asphalt

Cracking Analysis of Asphalt Mixture Using Semi-circle Bending Method

Extended Finite Element Modeling of Hot Mix Asphalt Based on the Semi-Circular Bending Test

Viscoelastic Fracture Analysis of Asphalt Concrete Pavement with Cracks

Compaction method and specimen geometry effect on the fracture properties of asphalt concrete in the SCB test at intermediate temperature

Advanced testing and characterization of low-temperature cracking in bitumen and mastic

Toughness modification of SBS/CRMA on epoxy asphalt: curing behaviour and low-temperature cracking characteristic analysis

Study on the correlation between spatial variability of asphalt mixture material parameters and fracture performance

Structural and mechanical evolution of the multiphase asphalt rubber during aging based on micromechanical back-calculation and experimental methods