Abstract:As typical phenolic resin-based ablative materials, the high silica/phenolic and carbon/phenolic composites are widely used in aerospace field. The specific heat of the carbonized ablators after ablation is an important thermophysical parameter in the process of heat transfer, but it is rarely reported. In this investigation, the carbonized samples of the high silica/phenolic and carbon/phenolic were obtained through carbonization experiments, and the specific heat of the carbonized samples was determined by a 3D DSC from 150 \(^{\circ }\hbox {C}\) to 970 \(^{\circ }\hbox {C}\). Structural and compositional characterizations were performed to determine the mass fractions of the fiber and the carbonized product of phenolic which are the two constituents of the carbonized samples, while the specific heat of each constituent was also measured by 3D DSC. The masses of the carbonized samples were reduced when heated to a high temperature in the specific heat measurements, due to the thermal degradation of the carbonized product of phenolic resin in the carbonized samples. The raw experimental specific heat of the two carbonized samples and the carbonized product of phenolic resin was modified according to the quality changes of the carbonized samples presented by TGA results. Based on the mass fraction and the specific heat of each constituent, a weighted average method was adopted to obtain the calculated results of the carbonized samples. Due to the unconsolidated property of the fiber samples which impacts the reliability of the DSC measurement, there is a certain deviation between the experimental and calculated results of the carbonized samples. Considering the similarity of composition and structure, the data of quartz glass and graphite were used to substitute the specific heat of the high silica fiber and carbon fiber, respectively, resulting in better agreements with the experimental ones. Furthermore, the accurate specific heat of the high silica fiber and carbon fiber bundles was obtained by inversion, enabling the prediction of the specific heat of the carbonized ablators with different constituent mass fractions by means of the weighted average method in engineering.

Physical Characteristics of One Carbon Phenolic Material Under High-Speed Symmetric Loading

High-strain Rate Compressive Behavior of Douglas Fir and Glubam

Evaluation of Interfacial Properties of Atmospheric Pressure Plasma-Treated Cnt-Phenolic Composites by Dual Matrix Fragmentation and Acoustic Emission Tests

Spallation Study on a Porous Phenolic Material

Research on high-temperature mechanical behaviour of carbon/phenolic composites under ultra-high heating rates

Experimental Research on the High‐temperature Compression Mechanical Properties of Carbon/phenolic Composites in Rapid Carbonization Conditions

Research on the Quasi-static and Dynamic Properties and Constitutive Relation of Carbon Fiber-reinforced Phenolic Composite

Effects of Carbon Nanotubes and Carbon Fiber Reinforcements on Thermal Conductivity and Ablation Properties of Carbon/phenolic Composites

Evaluation of the Effective Properties of High Silica/Phenolic Composite under Volumetric Ablation Condition

Fabrication And Heat-Insolation Of A Novel Low-Density And Low Thermal Conductivity Carbon/Phenolic Composite

Experimental Study Of In-Plane Mechanical Performance Of Carbon/Glass Hybrid Woven Composite At Different Strain Rates

Dynamic response of phenolic resin and its carbon-nanotube composites to shock wave loading

An Equation of State for New Type Carbon Fiber-Reinforced Bakelite

Degradation in compressive strength of silica/phenolic composites subjected to thermal and mechanical loading

Evaluation of Inter-Laminar Shear Performance of Carbon Fiber-Reinforced Composite under Quasi-Static and High-Strain-Rate Loading

Mechanical Properties and Fracture Mechanisms of Low-Density Fiber Preforms Reinforced Phenolic Aerogel Composites

Effect of surface-treated carbon nanotubes on the mechanical and tribological performances of phenolic resin

Experimental Study of In-plane Mechanical Properties of Carbon Fibre Woven Composite at Different Strain Rates

Experimental Investigation on the Specific Heat of Carbonized Phenolic Resin-Based Ablative Materials

Strain Rate and Temperature Effect on Mechanical Properties and Failure of 3D Needle-Punched Carbon/Carbon Composites under Dynamic Loading

Compressive Failure of Carbon/Epoxy Laminate Composites under High Impact Loading