Abstract:As a newly emerged active flow control technique, micro blowing/suction has shown a great potential in reducing the skin friction of turbulent flows. Throughout comprehensive analyses of active flow control of micro blowing/suction devices for a NACA0015 airfoil by means of CFD technique, the effects on various characteristics such as lift and drag coefficients and separation areas are investigated in this study. The control devices were placed at 12%c, 30%c and 70%c from the leading edge (c is the chord length of the airfoil), respectively. The corresponding trends of flow separation control at these locations were analyzed with a varied range of angle of attacks (AOA). The two- and three-dimensional incompressible unsteady detached-eddy simulation (DES) was used, along with the k-e turbulence model, in solving the flow problem. The numerical computational results have demonstrated that: (1) Installing micro blowing/suction devices near the separation point is more efficient, as blowing can mix the jet flow and the incoming flow to energize the turbulent kinetic energy and suction can mitigate the flow of low turbulent kinetic energy, which leads to a result of reducing the separation. (2) Suction sometime has more effective influence than blowing, when the flow control devices are placed at 12%c and 30%c. When the control device is placed at 70%c, the effects of lift enhancement and drag reduction are almost the same regardless of blowing and/or suction method. When the AOA is less than 18°, both methods can achieve the goal of lift enhancement and drag reduction. When the AOA is larger than 18°, neither blowing nor suction is efficient. (3) The 3-D numerical simulation shows that the vortex structure evolves from a 2-D pattern near the separation point to a 3-D pattern in the downstream. However the characteristics of flow separation control over a 3-D airfoil simulation agrees well with 2-D numerical results. (4) Blowing at 30%c can move the separation point downstream from 70%c to 80%c at AOA=11°.

Optimization of suction control on separation flow around an airfoil at low Reynolds number

Aerodynamic Optimization Design of Airfoil Configurations Based on Cascade Feedforward Neural Network

Particle Swarm Optimization of Aerodynamic Shapes with Nonuniform Shape Parameter–Based Radial Basis Function

Multiobjective Shape Optimization of A Hypersonic Lifting Body Using A Correlation-Based Transition Model

Effects of Micro Blowing/suction Flow Control Devices on a NACA0015 Airfoil

Experimental and Numerical Studies on Aerodynamic Control of NACA 4418 Airfoil with a Rotating Cylinder

Sensitivity-Based Parameterization for Aerodynamic Shape Global Optimization

Multi-Objective Optimization of Low Reynolds Number Airfoil Using Convolutional Neural Network and Non-Dominated Sorting Genetic Algorithm

Multi-objective robust airfoil optimization based on non-uniform rational B-spline (NURBS) representation

Airfoil shape optimization using genetic algorithm coupled deep neural networks

A Study of Multi-Objective Aerodynamic Optimization Design for Variable Camber Airfoils and High Lift Devices

Airfoil Optimization Using a Machine Learning-Based Optimization Algorithm

Optimizing NACA Airfoil Thickness Function Parameters for Maximum Lift-to-Drag Ratio

A Fast Multiobjective Optimization Approach to S-duct Scoop Inlets Design with Both Inflow and Outflow

Airfoil Shape Optimization: Comparative Study of Meta-heuristic Algorithms, Airfoil Parameterization Methods and Reynolds Number Impact

Multi-objective Optimization of a Low Specific Speed Centrifugal Pump Using an Evolutionary Algorithm

Application of a PCA-DBN-based Surrogate Model to Robust Aerodynamic Design Optimization

Aerodynamic Optimization Method for Propeller Airfoil Based on DBO-BP and NSWOA

Machine learning-based optimization of a pitching airfoil performance in dynamic stall conditions using a suction controller

Performance optimization and investigation of flow phenomena on tidal turbine blade airfoil considering cavitation and roughness

Multi-fidelity deep neural network surrogate model for aerodynamic shape optimization