Abstract:Masonry structures often exhibit poor seismic performance during earthquakes owing to their low material strength, structural integrity, and ductility. To address the mechanism of in-plane damage and collapse of masonry walls subjected to earthquake ground motion, three full-size brick walls, one with structural columns and two without structural columns, were designed and constructed in this experimental study to quantitatively investigate the effect of structural columns on the seismic performance of masonry walls. Quasi-static tests of masonry walls subjected to cyclic lateral loading were conducted using electrohydraulic servo actuators. The in-plane damage evolution and failure mode of the masonry walls under lateral loading were investigated. A numerical model with a novel plastic damage constitutive model of masonry was established. The accuracy of this model and the calculation results were verified by comparing them with the crack development and mechanical property curves obtained from the experiments. Based on the numerical model, a parametric analysis was conducted to investigate the influence of critical factors, such as mortar strength, vertical load, and height-to-width ratio, on the seismic performance of masonry structures. The test results showed that structural columns can effectively improve the performance of masonry structures. Properly installed structural columns can improve the peak load-bearing capacity, ductility, and energy dissipation of masonry structures. The masonry damage constitutive model used in this study could simulate the damage to masonry wall specimens well and reflect the hysteretic curves of the specimens within an acceptable range of accuracy. Thus, it provides a valuable reference for physical experiments. An appropriate mortar strength and vertical compressive stress can effectively enhance the load-bearing capacity of masonry structures within a certain range. For structural column walls. Walls with mortar strengths (average compressive strength) of 12.5 MPa, 10 MPa, 7.5 MPa, and 5 MPa showed an increase in peak bearing capacity of 26.2 %, 23.9 %, 18.5 %, and 9.4 %, respectively, compared to walls with mortar strengths (average compressive strength) of 2.5 Mpa. The aspect ratio had a significant impact on the shear load-bearing capacity of the masonry walls. An increase in the aspect ratio led to a transition from shear failure to flexural failure and a subsequent decrease in shear load-bearing capacity. For masonry walls with structural columns, increasing the diameter of the longitudinal steel in the structural columns can enhance the load-bearing capacity of the masonry wall, resulting in a significant improvement in its overall performance.

UNIAXIAL COMPRESSION ELASTIC-PLASTIC DAMAGE MODEL WITH DOUBLE PARAMETERS OF BRICK MASONRY

Research on Stochastic Damage Constitutive Relation of Masonry Subjected to Axial Loading

Damage Based Constitutive Model for Predicting the Performance Degradation of Concrete

Slip-enhanced plastic-damage constitutive model for masonry structures

About the Use of Concrete Damage Plasticity for Modeling Masonry Post-Elastic Behavior

A robust computational strategy for failure prediction of masonry structures using an improved multi‐surface damage‐plastic based interface model

An Elastoplastic Damage Constitutive Model for Concrete Considering Unilateral Effects

A Damage Model of Concrete including Hysteretic Effect under Cyclic Loading

Damage Constitutive Model for Concrete under Uniaxial Stress Conditions

Multi-axial elasto-plastic damage constitutive model for concrete

An elastoplastic damage model of concrete under cyclic loading and its numerical implementation

Uniaxial Compression Behavior Of Cement Mortar And Its Damage-Constitutive Model Based On Energy Theory

Calibration of a concrete damage plasticity model used to simulate the material components of unreinforced masonry reinforced concrete infill frames

Damage evolution and failure mechanism of masonry walls under in-plane cyclic loading

A Practical Elastic Plastic Damage Model for Concrete

The Effectiveness of CFRP- and Auxetic Fabric-Strengthened Brick Masonry under Axial Compression: A Numerical Investigation

Plastic-Damage Model for Cyclic Loading of Concrete Structures

A Elastic Plastic Viscous-Damage Model For Concrete Considering Strain Rate Effect And Application

STATISTICAL DAMAGE MODEL OF CONCRETE UNDER UNIAXIAL TENSION CONSIDERING DYNAMIC STRAIN-RATE EFFECT

A plastic-damage uniaxial compression constitutive of concrete

GRADUAL DAMAGE ANALYSIS FOR UNREINFORCED MASONRY WALL UNDER SHEAR-COMPRESSION LOADS