Abstract:HEPS is a new generation synchrotron facility with a stringent requirement of very low emittance. The key technology difficulties are supposed to be overcome during the stage of HEPS-TF. There are two projects in progress for mechanical and alignment system. One is the development of precision auto-tuning magnet girder, to meet the requirement of beam based alignment in tunnel, the other is the study on vibrating-wire alignment technique to improve alignment accuracy of magnets on a girder. This paper will describe the design and progress of both projects. INTRODUCTION HEPS storage ring consists of 48 7BA achromats, with the circumference of 1296m. Each arc section is about 27m. Girders provide firm support and precise positioning for magnets. There are 7 Magnet-Girder modules with 4 different sizes in an arc section, as shown in Fig.1. Each module will be pre-assembled, with components aligned, prior to installation in tunnel. Figure 1: One arc section (1/48). In order to achieve a very low emittance, magnetic centers should coincide with the theoretical orbit as much as possible. On the other hand, to close beam orbit may be rather difficult because of the large diameter of the storage ring and the small size of the beam. Therefor the physicists put forward stringent requirements to mechanical and alignment system, as shown in Table 1. The alignment error between magnets on a girder should be less than 30μm in both horizontal and vertical direction. And that between girders in tunnel should be less than 50μm after the first-time installation. Besides, the girder should be capable of doing beam-based alignment remotely to minimize the magnets position error during the runtime. Table 1: Alignment Tolerance Tolerances Magnet to Magnet Girder to Girder Horizontal 30μm 50μm Vertical 30μm 50μm The regular alignment method mostly rely on laser tracker and traditional girder design is more applying to be manipulated by hand in tunnel, and that would accumulate lots of errors in several steps and the final error usually more than 0.1mm, which could not meet the requirements of HEPS. So it is necessary to develop some new technology and the difficulties are supposed to be overcome during the stage of HEPS-TF. Based on this, there are two R&D projects on study: One is the Development of precision auto-tuning magnet girder, which could be manipulated through control system with the position monitored by sensors, to fulfil the alignment in tunnel, with or without beam. The other is the Research on vibrating-wire alignment technique, based on the measurement of magnetic center, to prealign multipole-magnets on a girder. These study will be critical for HEPS to realize the final goal of emittance.

Research on structure design under cryogenic effect in cryogenic permanent magnet undulator of high energy photon source

Study on the influence of gap dependent error on the cryogenic permanent magnet undulator performance

Effect Analyses of Thermal Deformation on Magnetic Performance of the CPMU Prototype in SSRF

Performance investigation of conduction-cooled cryogenic permanent magnet undulator at high beam currents

Design, Construction and Testing of the Prototype Cryogenic Circulation Centrifugal Pump for the High Energy Photon Source

Magnetic Field Optimization of a Novel Hybrid Permanent Undulator

Research on the comprehensive performance of PrFeB magnets for synchrotron radiation and free electron laser

Development and Operation of a Pr2Fe14B Based Cryogenic Permanent Magnet Undulator for a High Spatial Resolution X-ray Beamline

Research on Magnetic Properties of Nd(Pr)FeB Magnet for Cryogenic Permanent-Magnet Undulator of SSRF

Design and Analysis of Mechanical Structure for On-Board HTS Magnets Subjected to High Acceleration

Design and Progress on Mechanical & Alignment System for HEPS-TF

Optimized Design Considerations for Hybrid Undulator

Development of a superconducting undulator cryostat based on the thermosiphon effect

Design and Test of A Short Mockup Magnet for the Superconducting Undulator at the Ssrf

The Online Undulator Magnetic Field Measurement System

Development and tests of the 499.8 MHz srf cryomodules for HEPS

Conceptual Design of the Cryostat for the Superconducting Outsert of the 40 T Hybrid Magnet

Magnetic Field Measurement, Shimming and Processing for 230 MeV Superconducting Cyclotron Main Magnet

Design of End Magnetic Structures for Shanghai DUV-FEL Hybrid Undulators

Cooling Design for the Magnetic Structure of SHINE Superconducting Undulator

Design of Follow-Up Superconducting Cusp Magnetic Field and System Performance Analysis of Czochralski Single Crystal Furnace