Photoluminescence Of Silica Gels

韩银花,林君**,张洪杰

2001-01-01

Abstract:In this review the process for the preparation of silica gels via sol-gel method is described briefly, and the luminescent properties and mechanisms for the sol-gel derived silica gels (aerogel, xerogel and organic hybrid gel) are summarized.

What problem does this paper attempt to address?

Photoluminescence Property of ZnO–SiO2composites Synthesized by Sol–gel Method

HP He,YX Wang,YM Zou

DOI: https://doi.org/10.1088/0022-3727/36/23/017

2003-01-01

Abstract:The room temperature photoluminescence property of ZnO particles embedded in sol-gel silica was investigated. Three ZnO emissions at about 3.25 eV (ultraviolet (UV)), 2.8 eV (blue), and 2.45 eV (green) were observed. The blue and green emissions were ascribed to interstitial zinc and oxygen vacancy defects in ZnO. At heating temperatures above 900degreesC, the interaction of ZnO with SiO2 gave rise to Zn2SiO4, which enhanced the green emission markedly by limiting the oxidation process of oxygen vacancy. Heating in low oxygen pressure was found to enhance the UV emission substantially. The effects of heating temperature and ambient on blue and green emissions were also discussed.
Photoluminescence of Ge Nanoparticles Embedded in Sio2 Glasses Fabricated by A Sol-Gel Method

Hq Yang,Xj Wang,Hz Shi,Sh Xie,Fj Wang,Xx Gu,X Yao

DOI: https://doi.org/10.1063/1.1506943

IF: 4

2002-01-01

Applied Physics Letters

Abstract:Ge nanoparticles with different sizes in silica glasses were prepared by a sol-gel method using Cl-3-Ge-C2H4-COOH as a Ge source. The size of the Ge nanoparticles decreases with a reduction in the content of Ge in the starting materials, and thus the optical absorption edge shifts to a higher energy. Silica gel glasses doped with Ge nanoparticles showed a strong room-temperature photoluminescence with peaks at, 568, 607, 672, 722, and 775 nm. The peak position of photoluminescence spectrum scarcely depends on the Ge/Si ratio. However, the photoluminescence intensity increases sharply as the Ge/Si ratio is reduced. The photoluminescence arises from the Ge clusters of diameter of <1-2 nm with a molecular character instead of nanocrystalline Ge with the diamond structure. (C) 2002 American Institute of Physics. [DOI: 10.1063/1.1506943].
Room Temperature Photoluminescence Property of Boron-Doped Sol–gel Silica

Haiping He,Yuxia Wang,Yousheng Zou

DOI: https://doi.org/10.1016/j.materresbull.2004.02.012

IF: 5.6

2004-01-01

Materials Research Bulletin

Abstract:Room temperature photoluminescence (PL) of boron-doped silica synthesized by a combined sol–gel and heating process has been investigated. The broad PL band has been resolved into three components centered at 3.7, 3.35 and 2.7 eV, which are assigned to non-bridging oxygen hole centers (NBOHC), carbon-related impurity, and two-fold coordinated silicon atoms, respectively. The intensities of the 3.35 and 2.7 eV bands decrease with the heating temperature increasing, due to oxidation of the corresponding luminescent centers. The effect of boron doping on the formation of intrinsic defects in silica is discussed.
Visible Room-Temperature Photoluminescence of Ge-doped SiO2 Glasses Fabricated by a Sol–gel Process

Heqing Yang,Xi Yao,Xingjun Wang,Xiaoxiao Gu,Fujian Wang

DOI: https://doi.org/10.1016/j.optmat.2005.11.011

IF: 3.754

2007-01-01

Optical Materials

Abstract:Ge-doped SiO2 glasses are prepared by a sol–gel method using ethyl silicate (Si(OC2H5)4) and 3-trichologermanium propanoic acid (Cl3GeCH2CH2COOH) as starting materials. The Ge-doped SiO2 glasses show a strong room-temperature photoluminescence with peaks at 585 and 654nm under the excitation of the 514.5nm line of an Ar+ laser. The peak position of photoluminescence spectrum weakly depends on the Ge/Si ratio. The photoluminescence intensity increases sharply as the Ge/Si ratio is increased. The Ge-doped SiO2 gel glasses were characterized by X-ray diffraction, X-ray photoelectron spectroscopy and transmission electron microscopy. It reveals that Ge atoms exist as amorphous GeO2 particles in the gel glasses. The size of the amorphous Ge oxide nanoparticles increases with an increase in the content of Ge in the starting materials, and thus optical absorption edge is shifted towards longer wavelengths. The 585 and 654nm emissions may originate from the small “peroxy radical” and the nonbridging oxygens at the interface between the amorphous GeO2 core and outer SiO2 matrix, respectively.
Synthesis and Room Temperature Photo Luminescence of Agi Nanoparticles Embedded in Silica Sol-Gel Coating

HP He,YX Wang,HW Chen

DOI: https://doi.org/10.1016/j.ssi.2004.07.068

IF: 3.699

2004-01-01

Solid State Ionics

Abstract:AgI nanoparticles embedded in sol–gel silica coating were synthesized by a soaking–heating method. X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), optical reflection, and photoluminescence (PL) measurements were used to characterize the coating. The size of the AgI particles was about 10–40 nm. A red shift of ∼10 nm on the absorption edge as well as the formation of a band tail was observed. The PL spectrum of the coating exhibits main emissions at 333, 370, 435, 470, and 510 nm. The former two corresponding to nonbridging oxygen hole centers (NBOHC) and E′ centers in silica, respectively. The emission at 435 nm is ascribed to radiative excitonic recombination of AgI, while the 470-nm one is associated with a transition between the tail of the conduction band (CB) and the valence band (VB). The emission at 510 nm may arise from free Ag+ ions or defects.
Room temperature photoluminescence from Zr4+-doped sol–gel silica

Haiping He,Yuxia Wang,Yi Wang,Youming Zou,Zheng Chen,Shuai Yuan

DOI: https://doi.org/10.1016/S0038-1098(03)00276-X

IF: 1.934

2003-01-01

Solid State Communications

Abstract:Intense room-temperature photoluminescence (PL) from the UV to the green region was observed from Zr4+-doped silica synthesized by a sol–gel process using tetraethoxysilane as the precursor, followed by thermal treatment at 500 °C in air. The wide PL band can be resolved into three components centered at 3.70, 3.25, and 2.65eV, respectively. The intensity of the 3.25 and 2.65eV PL bands was greatly enhanced compared with pure sol–gel silica. The 3.70eV emission was assigned to non-bridging oxygen hole centers, while the 2.65eV one originated from neutral oxygen vacancies (VO). The 3.25eV PL band was most likely associated with E′ centers, as supported by electron spin resonance measurement. It was proposed that the Zr4+-doping leads to oxygen deficiency in the silica, thus resulting in enhancement of the density of VO and E′ center defects.
Progress in Luminescent Films Prepared by Sol-Gel Process

J Lin,ML Pang,YH Han,YH Zhou,M Yu,HJ Zhang

DOI: https://doi.org/10.3321/j.issn:1001-4861.2001.02.001

2001-01-01

Abstract:In this paper, state of the art for luminescent films prepared by sol-gel process has been reviewed. The basic process and characteristics for the synthesis of luminescent films via sol-gel method, Characterization methods for the films and the current status for the development and application of luminescent films are discussed in the context, An elucidation has been made on the luminescent films classified by composition, including inorganic luminescent films and organic/inorganic hybrid luminescent films. The sol-gel derived luminescent films have found applications in the display devices for photoluminescence, electroluminescence, cathodoluminescence and field emission etc. Finally, the future development tendency for the luminescent films are forecasted.
Photoluminescence of organic–inorganic hybrid SiO2 xerogels

Yinhua Han,Jun Lin,Hongjie Zhang

DOI: https://doi.org/10.1016/S0167-577X(01)00599-7

IF: 3

2002-01-01

Materials Letters

Abstract:Organic–inorganic hybrid SiO2 xerogels were prepared by the sol–gel method under various preparation conditions and compositions by using tetraethoxysilane (TEOS), (3-aminopropyl) triethoxysilane (APS), (3-glycidoxypropyl) trimethoxysilane (GPS), organic acid (CH3COOH) and inorganic acids (HCl, HNO3, H2SO4) as the main precursors. Luminescence and FT-IR spectra were used to characterize the resulted hybrid SiO2 xerogels. The result of FT-IR spectrum shows that the xerogels are composed of non-crystalline SiOSi networks containing some organic groups such as NH, CH and OH. Under the excitation of 365 nm, all the hybrid xerogels exhibit strong luminescence in the blue region, but the emission intensity and position depend on the starting precursor compositions to a large extent. Suitable amount of polyethylene glycol (PEG500 and PEG10000) in the hybrid xerogels can enhance the emission intensity. Additionally, the emission intensity of the hybrid xerogels increases with heat treatment temperature in the range of ambient to 200 °C, and vacuum condition is also able to enhance the emission intensity.
Preparation of C60-doped Silica Aerogels and the Study of Photoluminescence Properties

B Zhou,J Wang,L Zhao,J Shen,ZS Deng,YF Li

DOI: https://doi.org/10.1116/1.1306279

2000-01-01

Journal of Vacuum Science & Technology B Microelectronics and Nanometer Structures Processing Measurement and Phenomena

Abstract:The preparation of C60-doped silica aerogels by the sol-gel process is described in this article. Fourier transfer infrared spectra, time-of-flight mass spectroscopy, and transmission electron microscopy showed that C60 was incorporated into silica aerogels, and the C60 structure was retained in the preparation process. The C60-doped silica aerogels emitted intense visible light (2.10 eV) under Ar+ laser (488 nm) excitation at room temperature, and the photoluminescence peak was “blueshifted” when compared with C60’s. The blueshift is explained based on a quantum confinement effect.
Progress in Research on Luminescence Properties of Porous Sillicon-based Composite

赵毅,杨德仁,周成瑶,阙端麟

DOI: https://doi.org/10.3321/j.issn:1005-023x.2003.09.012

2003-01-01

Abstract:This paper reviews briefly research on luminescence properties of porous silicon-based composite. Composition systems and their luminescence properties are discussed, followed by a review of the factors that affect luminescence properties of the composition and the synthetic methods of porous silicon-based composite. Furthermore , the mechanism of luminescence of porous silicon-based composite is discussed. Finally current problems and developing tendency are described.
Photoluminescence, Composition and Microstructure of Porous Silicon Prepared by Different Substrates

Yue Zhao,Dong-Sheng Li,Wen-Bin Sang,De-Ren Yang,Min-Hua Jiang

DOI: https://doi.org/10.1142/s0217984908015280

2008-01-01

Modern Physics Letters B

Abstract:In this paper, the microstructure of porous silicon was discussed by scanning electron microscopy and Raman spectra. The compositions of the samples were studied by Xray diffraction and electron diffraction. The luminescent properties of porous silicon were explored by the PL measurements. The results showed that the structure of the top porous silicon prepared by epitaxial silicon consists of meso-pores and that of the underlying porous silicon consists of macro-pores. Furthermore, the structure of porous silicon prepared by heavily doped silicon is made of nano-pores. The composition of porous silicon consists of the single-crystal phase, poly-crystal phase and amorphous-crystal phase, respectively. In addition, the luminescence of porous silicon may come from the defects on the silicon-rod surface and in Si complexes including siloxene, Si oxide and Si hydrides, and may not be related to amorphous phase and nano-phase.
Optical Properties Of Free-Standing Gelatin-Si Nanoparticle Composite Films And Gelatin-Si-Au Nanoparticle Composite Films

Li Shi,Ting Yu,Luwei Sun,Xiaodong Pi,Xinsheng Peng

DOI: https://doi.org/10.1039/c3cp53618a

IF: 3.3

2013-01-01

Physical Chemistry Chemical Physics

Abstract:A free-standing fluorescent gelatin-Si nanoparticle composite thin film is facilely prepared by means of a filtration technique assisted by porous copper hydroxide nanostrands as a sacrificial layer. The as-prepared gelatin-Si nanoparticle composite film is greatly portable, flexible, transparent and freestanding. The most important advantage is its robust storage stability stored in ambient air, which make it promising for various applications. Meanwhile, a gelatin-Si-Au nanoparticle composite film is also successfully prepared by the formation of Au NPs in a gelatin-Si nanoparticle composite film through the in situ reduction of HAuCl4 at room temperature. The photoluminescence (PL) quenching and blue shift in the peak of the emission spectra occur due to the energy transfer from Si NPs to Au NPs. By varying the amount and size of Au NPs incorporated into the gelatin-Si nanoparticle composite film, the energy transfer efficiency can be controlled. This is a general method to prepare metal-semiconductor hybrid fluorescent nanomaterials, which offers the possibility of tuning the luminescence intensity and wavelength of the emitted light.
Lanthanide–based luminescent hybrid silica materials prepared by sol-gel methodologies: a review

Leandro Trupp,María Claudia Marchi,Beatriz C. Barja

DOI: https://doi.org/10.1007/s10971-021-05678-9

2021-11-24

Abstract:Research in the field of lanthanide-based luminescent hybrid silica materials has grown substantially in the last decades, given the unique spectroscopic properties of lanthanide(III) complexes and the stability and biocompatibility of silica hosts. The versatility of the sol-gel technique to produce glasses, fibers, films, nanoparticles and ceramics has turned it into one of the most powerful methods to achieve such goals. This review describes the most commonly used sol-gel strategies to insert a luminescent lanthanide(III) complex inside a silica host and their potential applications, with the aim to help in the choice for a particular functional material. In particular, the focus is set on the different approaches developed to embed the visible or near infrared emitting guest in the silica matrix, either by entrapment within the three-dimensional network, anchoring on the surface of a nano or microparticle or inclusion in a mesopore. In addition, the usual organic ligands and the different functionalization strategies are discussed.

materials science, ceramics
Synthesis Process and Luminescence Behavior of Rho-Hydroxybenzoic Acid-Terbium Complex Doped Silica Nanoparticles

Zou Yongjin,Wang Feng,Fan Xianping

DOI: https://doi.org/10.3321/j.issn:1002-185x.2008.z2.126

2008-01-01

Abstract:Synthesis process and luminescence behavior of p-hydroxybenzoic acid-terbium complex doped silica nanoparticle have been investigated. The rho-hydroxybenzoic acid-terbium complexes were in-situ synthesized during formation of silica nanoparticle. The colloidal so lutions of the silica nanoparticles show bright green luminescence upon short wavelength UV irradiation.
Photoluminescence and Photoluminescence Excitation of Si Aerogels Prepared by Supercritical Drying

GL Guo,DS Xu,GQ Yao,YQ Tang,LD Zhang,J Lin,SY Ma,JQ Duan,BR Zhang,GG Qin

DOI: https://doi.org/10.1088/0256-307x/13/1/017

1996-01-01

Chinese Physics Letters

Abstract:Si aerogel, the porous silicon with ultra high porosity, has been prepared by the technique of anodization followed by supercritical drying. Its photoluminescence, photoluminescence excitation and morphological features exhibit novel characteristics from those of the conventionally anodized porous silicon. We observed the differences between the Si aerogels made from (100) and (111) crystalline Si.
Supercritical drying preparation and fractal structure of blue luminescent silica aerogel

S.B. Xiong,Z.M. Ye,Z.G. Liu,W.P. Ding,X.Q. Zheng,Y.P. Zhu,C.Y. Lin

DOI: https://doi.org/10.1016/S0167-577X(97)00028-1

IF: 3

1997-01-01

Materials Letters

Abstract:A blue luminescent silica monolithic aerogel was prepared by a sol-gel process followed supercritical drying. The as-prepared silica aerogels are transparent and exhibit blue luminescence excited by a near UV light of 365 nm wavelength. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) revealed that the monolithic aerogel had micropores and nanopores. Small angle X-ray scattering analysis showed that our aerogel had a fractal dimension of 1.96, which is consistent with that calculated by chemically limited cluster-cluster aggregation from a monodispersed particle system. The luminescent mechanisms are also discussed.
Preparation of Methyltrimethoxysilane Derived Silica Aerogel Films via Ambient Pressure Drying

Li Jin,Zhao Gaoling,Zhao Chang,Meng Weijie,Han Gaorong

2016-01-01

Rare Metal Materials and Engineering

Abstract:It is essential for the silicon source as an important part of the precursor for preparing silica aerogel films with integrity structure and excellent performance. Silica aerogel films were prepared using methyltrimethoxysilane (MTMS) as alkyl-functional precursor via sol-gel process and ambient pressure drying method, and the whole process was greatly simplified. The microstructure, refractivity and porosity of silica aerogel films were characterized by SEM, spectroscopic ellipsometry and TGA. The effect of the amount of the solvent and different heat treating temperatures on the structure and performance of silica film was investigated. The result indicate that with heat treating temperature increaseing, porosity and transmittance of the film increase.
Luminescence of Bi3+ Ions and Energy-Transfer from Bi3+ Ions to Eu3+ Ions in Silica Glasses Prepared by the Sol-Gel Process

MQ WANG,XP FAN,GH XIONG

DOI: https://doi.org/10.1016/0022-3697(95)00008-9

IF: 4.383

1995-01-01

Journal of Physics and Chemistry of Solids

Abstract:Luminescence of Bi3+ ions and energy transfer from Bi3+ ions to Eu3+ ions in silica glasses prepared by the sol-gel process have been investigated. The results showed that the excitation band of Bi3+ ions corresponds to the 1S0 → 1P1 transition and emission spectra consists of a single broad band without structure centred at 395 nm, which corresponds to 3P1 → 1S0 transition. When a small amount of Bi3+ ions was introduced to 1 mol% Eu3+ ions the doped silica gel glass emission intensity of Eu3+ ions got significantly stronger, which suggests very efficient energy transfer from Bi3+ ions to Eu3+ ions. It can be assigned to significant energy overlap between the emission band of the Bi3+ ion and the excitation band of the Eu3+ ion. However, due to a larger energy overlap between emission and excitation bands of Bi3+, when Bi3+ ion concentration in silica gel glasses was more than 0.5 mol% the probability of energy transfer between Bi3+ ions increased rapidly and the probability of energy transfer from Bi3+ ions to Eu3+ ions decreased relatively. As a consequence, the sensitized effectiveness of the Bi3+ ion on the emission spectrum of the Eu3+ ion drastically decreased with increasing Bi3+ ion concentration.
Study of Eu3+-doped Luminescence Glasses Prepared by a Sol-Gel Process

XP FAN,MQ WANG,GH XIONG

DOI: https://doi.org/10.1016/0921-5107(93)90265-o

1993-01-01

Abstract:The formation of Eu3+-doped luminescence glasses prepared by sol-gel techniques and the spectroscopic properties of Eu3+ ions in dried gels and gel glasses were investigated. The results showed that most residual water and organic molecules in the dried gel had vaporized in the temperature range from room temperature to 200 °C, and careful heat treatment of the dried gel in a lower temperature range was required to obtain bulk Eu3+-doped luminescence glass. It was also found that the ratio of emission intensities of the 5D0→7F1 transition and 5D0→7F2 transition in dried gels was very different from that in gel glasses. The dependence of concentration on the Eu3+ emission intensity in dried gels and gel glasses was also investigated. In gel glasses, the dependence of concentration on the luminescence in the range 0.5–4 mol% Eu2O3 did not reveal any concentration quenching. Conversely, the optimum concentration of Eu2O3 for maximum luminescence intensity in dried gels was approximately 1 mol%. The phonon-assisted resonant energy transfer theory is expected to explain the concentration quenching of Eu3+ ion luminescence in dried gels.
PREPARATION OF FULLERENCE DOPED SILICA AEROGELS AND THE STUDY OF PHOTOLUMINESCENCE PROPERTIES

Zhou Bin,Wang Jue,Shen Jun,Weng Zhi-Nong,Deng Zhongsheng,Zhao Li,Li Yufen

DOI: https://doi.org/10.7498/aps.46.1437

1997-01-01

Abstract:Abstract This paper introduces the preparation of fullerence doped silica aerogels by “chemically doped” and sol gel process.The infrared spectra and time of flight mass spectra show that C 60 were successfully incorporated into the silica aerogel and the structures were retained in the fabrication process.Photoluminescence spectra shows that fullerence doped silica aerogels exhibit broad visible light under Ar + laser(488nm).The photoluminescence is blue shifted compared with pure C 60 .In this paper, we give an explanation to this blue shift.

Photoluminescence Of Silica Gels

Photoluminescence Property of ZnO–SiO2composites Synthesized by Sol–gel Method

Photoluminescence of Ge Nanoparticles Embedded in Sio2 Glasses Fabricated by A Sol-Gel Method

Room Temperature Photoluminescence Property of Boron-Doped Sol–gel Silica

Visible Room-Temperature Photoluminescence of Ge-doped SiO2 Glasses Fabricated by a Sol–gel Process

Synthesis and Room Temperature Photo Luminescence of Agi Nanoparticles Embedded in Silica Sol-Gel Coating

Room temperature photoluminescence from Zr4+-doped sol–gel silica

Progress in Luminescent Films Prepared by Sol-Gel Process

Photoluminescence of organic–inorganic hybrid SiO2 xerogels

Preparation of C60-doped Silica Aerogels and the Study of Photoluminescence Properties

Progress in Research on Luminescence Properties of Porous Sillicon-based Composite

Photoluminescence, Composition and Microstructure of Porous Silicon Prepared by Different Substrates

Optical Properties Of Free-Standing Gelatin-Si Nanoparticle Composite Films And Gelatin-Si-Au Nanoparticle Composite Films

Lanthanide–based luminescent hybrid silica materials prepared by sol-gel methodologies: a review

Synthesis Process and Luminescence Behavior of Rho-Hydroxybenzoic Acid-Terbium Complex Doped Silica Nanoparticles

Photoluminescence and Photoluminescence Excitation of Si Aerogels Prepared by Supercritical Drying

Supercritical drying preparation and fractal structure of blue luminescent silica aerogel

Preparation of Methyltrimethoxysilane Derived Silica Aerogel Films via Ambient Pressure Drying

Luminescence of Bi3+ Ions and Energy-Transfer from Bi3+ Ions to Eu3+ Ions in Silica Glasses Prepared by the Sol-Gel Process

Study of Eu3+-doped Luminescence Glasses Prepared by a Sol-Gel Process

PREPARATION OF FULLERENCE DOPED SILICA AEROGELS AND THE STUDY OF PHOTOLUMINESCENCE PROPERTIES