Abstract:In recent decades, geoelectrical methods have played a very important role in near-surface investigation. The most widely used of these methods is electrical resistivity tomography (ERT). Regardless of the forward and inversion algorithms used, the original data collected from a survey is the most important factor for quality of the resulted model. However, 3D electrical resistivity survey design continues to be based on data sets recorded using one or more of the standard electrode arrays. There is a recognized need for the 3D survey design to get better resolution using fewer data. Choosing suitable data from the comprehensive data set is a great approach. By reasonable selecting, better resolution can be obtained with fewer electrodes and measurements than conventional arrays. Previous research has demonstrated that the optimized survey design using the 'Compare R' method can give a nice performance.This paper adds target-oriented selection and modified the original 'Compare R' method. The survey design should be focused on specific target areas, which need a priori information about the subsurface properties. We select electrodes and configurations as the target set by the comprehensive set firstly which meets the requirements of the target area. The number of measurements and electrodes is much less than the comprehensive set and the model resolution matrix takes less time to calculate. At the next step for rank, we calculate the sensitivity matrix of the target set only once and then calculate the contribution degree of each measurement separately from it. The time of iterative calculation of the resolution matrix when measurements set changing is less than the original method.The traditional method of evaluating RMS is not appropriate for comparing the quality of collected data by different survey designs. SSIM (structural similarity index) gives more reliable measures of image similarity better than the RMS. The curves of SSIM values in three dimensions and the average SSIM are given as quantitative comparisons. Besides, the frequency of electrodes utilized given to guides on selecting the highest used electrodes. Finally, the curves of the average relative resolution S and the number of electrodes as the number of measurements increase are given, which proves the method works effectively.The results show the significance of using target-oriented optimized survey design, as it selects fewer electrodes and arrays than the original CR method. Also, it produces better resolution than conventional arrays and takes less calculation time. 3D SSIM, frequency of electrodes used, the relationship between average relative resolution, number of electrodes and number of measurements, these quantitative comparison methods can effectively evaluate the data collected in various survey designs.

Simulation and Application of a New Electromagnetic Resistivity Tool with Array Compensation Propagation While Drilling

Study on Numeric Simulation of Complex Resistivity Logging

Signal detection of lateral resistivity LWD based on C4D technique with oil-based drilling fluid

The Resistivity Imaging LWD Method Suitable for Oil-Based Drilling Fluid

A Novel Lateral Resistivity Logging-While-drilling (LWD) Method in Oil-Based Drilling Fluid

Reservoir evaluation method for complex resistivity using the borehole–surface electromagnetic method: A case study of an igneous reservoir in the K exploration area, China

Target-oriented Optimized Survey Design and Quantitative Comparison for 3D Electrical Resistivity Tomography

A New Logging-While-Drilling Method for Resistivity Measurement in Oil-Based Mud.

Analysis and Design of the Coils System for Electromagnetic Propagation Resistivity Logging Tools by Numerical Simulations

Coil optimization of ultra-deep azimuthal electromagnetic resistivity logging while drilling tool based on numerical simulation

A Novel Approach for Electromagnetic Logging While Drilling Data Processing

Parameter Inversion Based on Levenberg-Marquardt Algorithm for Layered Formation Using Electromagnetic Wave Resistivity Tool

Development of a Multi-Channel Array Resistivity Method Instrument System

Application of Vector Finite Element Method to Simulat Elogging-While-drilling Resistivity Tools

Calibration method of azimuth electromagnetic boundary detection logging while drilling based on air–seawater double-layer dielectric as reflection interface

Real-time forward modeling and inversion of logging-while-drilling electromagnetic measurements in horizontal wells

Simulation of Electromagnetic Logging-While-drilling Tools Using Vector Finite Element Methods

Grounded source transient electromagnetic 3D forward modeling with the spectral-element method and its application in hydraulic fracturing monitoring

Two-dimensional Inversion of CSAMT Data and Three-Dimensional Geological Mapping for Groundwater Exploration in Tongkeng Area, Hunan Province, China

Self-adaptive inversion method of electromagnetic-propagation resistivity logging while drilling data

Boundary Detection Capability and Influencing Factors of Electromagnetic Resistivity While Using Drilling Tools in a Horizontal Well