Abstract:To bring the potential power of the capacitively coupled contactless conductivity detection ((CD)-D-4) technique to full play and extend the application fields of (CD)-D-4, our previous work has developed a (CD)-D-4 sensor which is suitable for conductivity detection of electrolyte solution in industrial fields (Sensors and Actuators A 213 (2014) 1-8). With the introduction of series resonance principle, the (CD)-D-4 sensor can overcome the influence of coupling capacitances on conductivity measurement. By a specific design of shield configuration, the (CD)-D-4 sensor can overcome the influence of stray capacitances and the environment interference in industrial fields. Although the measurement performance of the (CD)-D-4 sensor is satisfactory and it is suitable for the conductivity detection in industrial fields, the input-output characteristic of the (CD)-D-4 sensor is non-monotonic, which may limit the practical applications of the (CD)-D-4 sensor. To overcome this drawback, an improved (CD)-D-4 sensor for conductivity detection in industrial fields has been developed. The basic conductivity measurement method (the series resonance principle) and the shield configuration of the improved (CD)-D-4 sensor are the same as those of the (CD)-D-4 sensor in our previous work. However, the measurement circuit of the detection path of the improved (CD)-D-4 sensor has been optimized. The one-inductor design has been replaced by a two-inductor design. With this optimization, the input-output characteristic of the improved (CD)-D-4 sensor is theoretically monotonic. Conductivity measurement experiments were carried out on four pipes with inner diameters of 1.8 mm, 3.3 mm, 5.0 mm and 7.6 mm, respectively. The experimental results indicate that the development of the improved (CD)-D-4 sensor is successful. In comparison with the previous (CD)-D-4 sensor, the measurement accuracy of the improved (CD)-D-4 sensor is comparable. But, the improved (CD)-D-4 sensor has the advantages of the monotonic input-output characteristic and the convenience for practical conductivity detection in industrial fields. Meanwhile, it is found that the input-output characteristic of the improved (CD)-D-4 sensor is nonlinear and the sensitivity of the improved (CD)-D-4 sensor decreases with the increase of conductivity. (C) 2015 Elsevier B.V. All rights reserved.

Signal detection of lateral resistivity LWD based on C4D technique with oil-based drilling fluid

The Resistivity Imaging LWD Method Suitable for Oil-Based Drilling Fluid

A Novel Lateral Resistivity Logging-While-drilling (LWD) Method in Oil-Based Drilling Fluid

A New Logging-While-Drilling Method for Resistivity Measurement in Oil-Based Mud.

Design and Implementation of an Industrial C4D Sensor for Conductivity Detection

A New Method of Capacitively Coupled Contactless Conductivity Detection Based on Series Resonance

Capacitively Coupled Contactless Conductivity Detection Based On Phase-Sensitive Demodulation Principle

Design of Capacitively Coupled Contactless Conductivity Detection Sensor

A C~4D-Based Measurement System of Gas-Liquid Two-Phase Flow

A new method for the velocity measurement of gas-liquid two-phase flow

A New Sensor for the Void Fraction Measurement of Gas-Liquid Two-Phase Flow

An Improved Capacitively Coupled Contactless Conductivity Detection Sensor for Industrial Applications

Induction Logging Through Casing by Detecting Lateral Waves: A Numerical Analysis

Design and optimization of a new type of contactless radial C4D sensor

A Low Excitation Working Frequency Capacitively Coupled Contactless Conductivity Detection (C4D) Sensor for Microfluidic Devices

Void Fraction Measurement Of Gas-Liquid Two-Phase Flow Based On (Cd)-D-4 Technique

A Contactless Conductivity Sensor Based on Capacitively Coupled Principle

On the Depth of Detection of Logging-While-drilling Resistivity Measurements for Looking-Around and Looking-Ahead Applications

Simulation of the Borehole Quasistatic Electric Field Excited by the Acoustic Wave During Logging While Drilling Due to Electrokinetic Effect

Simulation and Application of a New Electromagnetic Resistivity Tool with Array Compensation Propagation While Drilling

Coil optimization of ultra-deep azimuthal electromagnetic resistivity logging while drilling tool based on numerical simulation