Abstract:PURPOSETo study the change of ion precipitation and surface roughness of three dental alloys'coexisting in standard electrolyte solution, in order to provide a reference for the selection of clinical alloy materials.METHODSStandard samples of Ni-Cr alloy, Co-Cr alloy and Au-Ag-Pd alloy were prepared and divided into 5 groups: Ni-Cr alloy(group N), Co-Cr alloy(group C), Au-Ag-Pd alloy(Group A), Ni-Cr alloy contact with Au-Ag-Pd alloy(group NA), Ni-Cr alloy contact with Co-Cr alloy(group NC). All groups of alloys were soaked in standard electrolyte solution (T=37 ℃, pH=2.31) for 7 days. Inductively coupled plasma mass spectrometry (ICP-MS) was used to measure the amount of ions released from each group. The surface morphology of each group was observed and the surface roughness(Ra) was measured using atomic force microscope（AFM）. SPSS 18.0 software package was used for statistical analysis.RESULTSThe amount of nickel ions released from group N, NA, NC was (1.32±0.03) μg/cm2, (2.13±0.07) μg/cm2, (1.53±0.08) μg/cm2, respectively. Nickel ions of group NA and NC was significantly more than that of group N(P<0.05), nickel ions of group NA was significantly more than that of group NC(P<0.05). The amount of chromium ions released from group N, NA, NC was (0.06±0.01) μg/cm2, (0.08±0.01) μg/cm2, (0.05±0.01) μg/cm2, respectively, the amount of chromium ions of group NA was significantly more than that of group NC(P<0.05). The surface roughness of Ni-Cr alloy in group N, NA, NC was (4.60±0.16) nm, (5.37±0.08) nm, (5.04±0.15) nm, respectively. The surface roughness of Ni-Cr alloy in group NA and group NC was significantly larger than that in group N (P<0.05). When contact with Au-Ag-Pd alloy or Co-Cr alloy, the amount of nickel ions released and the surface roughness of Ni-Cr alloy both significantly increased. Compared with Co-Cr alloy, Au-Ag-Pd alloy caused Ni-Cr alloy to release more nickel, chromium ions and formed a rougher surface.

The correlation study between composition and corrosion resistance of dental non-noble metal under acidic environment

Influence of Fluoride-Containing Acidic Artificial Saliva on the Mechanical Properties of Nickel-Titanium Orthodontics Wires.

Change of corrosion Oil nickel-titanium arch wires in oral environment

The developments in corrosion and protection of dental alloys

An electrochemical study on corrosion behavior of three alloys in artificial saliva with different pH

Microstructure and Corrosion Resistance of Medical Cobalt-Based Alloys

The Effect on the Corrosion Resistance of Ti Alloy in the Artificial Saliva with Different pH Value

[Microbial Corrosion of Dental Alloy].

Research development of corrosion of titanium in the oral bioenvironment

Comparative Study on the Corrosion Behavior of Ti–Nb and TMA Alloys for Dental Application in Various Artificial Solutions

Analysis and Comparison of the Corrosive Behavior of Nickel-Based and Cobalt-Based Dental Alloys

The electrochemical behavior and surface analysis of Ti<sub>49.6</sub>Ni<sub>45.1</sub>Cu<sub>5</sub>Cr<sub>0.3</sub>alloy for orthodontic usage

Behavior of Two Dental Alloys as Ingot and Cast Crown in Artificial Saliva

The Electrochemical Behavior And Surface Analysis Of Ti49.6ni45.1cu5cr0.3 Alloy For Orthodontic Usage

A study of corrosion resistance of five dental alloys used for crowns

Surface analysis of nickel-chromium dental alloys

Composition and in vitro corrosion of orthodontic appliances

Effect of Ph Value and Fluoride Ions on Corrosion Resistance of Pure Ti and Ni-Cr-Ti Alloy in Artificial Saliva

[Change of Ion Precipitation and Surface Roughness of Three Dental Alloys Coexisting].

Corrosion behavior of Ti-39Nb alloy for dentistry

The Electrochemical Behavior and Surface Analysis of Ti50Ni47.2Co2.8 Alloy for Orthodontic Use